Results 1 to 10 of 24
Hybrid View
-
12-04-2014, 12:29 PM #1
I also want to get one variable out of the way. Is the razor from eBay not one of the blades from the "do not buy" (my words) list found in the library. If not what type or manufacture is it
A fool flaunts what wisdom he thinks he has, while a wise man will show that he is wise silently.
-
12-04-2014, 12:41 PM #2
- Join Date
- Oct 2014
- Location
- Rochester, NY
- Posts
- 24
Thanked: 0That's a little comforting because I was reading that it should only take 15-20 minutes even on new stones so after the 40 minute mark I was getting worried something wasn't right. None of my other stone have even done this, but then again I've never used these high grits before or even norton/niniwa stones before.
Not a 100% sure on the exact manufacture, think its "Ontario Cuttlery". I ran it buy you guys before I bought it, link to the thread is below.
http://straightrazorpalace.com/aucti...ce-honing.html
-
12-04-2014, 02:03 PM #3
Yes, lapping stones can take a while.
My Naniwa SS 1k and 3k both took at least 1hr under running water.
With my 8k I gave up after 2 separate 45 minute sessions.
With the 12k I gave up after 1hr.
The 8k and 12k still have about an inch of unlapped surface at each end, so I just keep the blade at the center and avoid these areas.
Cheers.Rule #32 – Enjoy the Little Things
-
12-04-2014, 02:20 PM #4
I'm the same when it comes to lapping/flattening my 8k and chosera 1k. Both seemed to take forever, but of course are very hard stones. I think I spent on the 8k at least an hour before setting aside till another day and then it still took about another hour and a half. I was using at the time a norton flattening stone. But for the method I like glen's method of filling the sink to where the water is just sitting above or on the surface of the stone (stone on bottom while holding the plate). To me this allows for constant movement of water to wash off the stones without splashing and just change out the water when needed. But the trickling water works ok too.
A fool flaunts what wisdom he thinks he has, while a wise man will show that he is wise silently.
-
12-04-2014, 02:56 PM #5
- Join Date
- Mar 2012
- Location
- Thunder Bay, Ontario, Canada
- Posts
- 17,251
Thanked: 3222Wow, I am astounded that it could take so long a time to lap a Naniwa SS hone. That has not been my experience with them. I have also seen plenty of warnings not to water soak Naniwa hones for a prolonged period of time on supplier web sites.
BobLife is a terminal illness in the end
-
12-04-2014, 05:25 PM #6
- Join Date
- Sep 2009
- Location
- SE Oklahoma/NE Texas
- Posts
- 7,285
- Blog Entries
- 4
Thanked: 1936Norton's are some pretty hard stones and it sounds like you got one shaped like a banana. If it's still a ways out, you may consider a more rough approach like some wet/dry sandpaper in a more coarse grit & then follow up with your DMT. Naniwa SS's on the other hand are one of the softer stones and if it's taking a long time you aren't getting enough water on the DMT to rinse out the "mud" so the diamond stone can cut.
This is a good task for you, it will teach you patience...which is most definitely required when honing razors. Take your time and sometimes you may have to walk away & come back when your head is right...just don't give up!Southeastern Oklahoma/Northeastern Texas helper. Please don't hesitate to contact me.
Thank you and God Bless, Scott
-
12-04-2014, 06:40 PM #7