Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24
Like Tree31Likes

Thread: 12,000 grit specialty stone

  1. #11
    Senior Member blabbermouth
    Join Date
    Dec 2014
    Location
    Virginia, USA
    Posts
    2,224
    Thanked: 481

    Default

    Quote Originally Posted by PaulKidd View Post
    Another lapping option is the Double Time lapping stone:

    https://www.sharpeningsupplies.com/D...P1545C282.aspx
    I think you would run into the same problem with that as the Norton plate. It may* come dead flat - at first. Not saying they're lying. Honestly the Norton plates are usually 'flat enough' out of the box, but better after break in (isn't everything?). But I'd wager it wouldn't stay that way long, and it will need flattening eventually.

  2. #12
    'with that said' cudarunner's Avatar
    Join Date
    Aug 2010
    Location
    Walla Walla in WA State USA
    Posts
    11,225
    Thanked: 4237

    Default

    Quote Originally Posted by k5MOW View Post
    OK I am thinking about doing the sandpaper idea. What grit wet dry sandpaper should I get.

    Thanks Roger
    With all due respect to everyone who has chimed in on the OP's question. I've used the Wet and Dry Sandpaper and while it will work, the DMT is a better tool and one that will be working for years to come.

    Here's what's involved with lapping a Norton hone.



    If the sandpaper is used be sure to pick up a piece of 1/4" glass that's about 12"x12" or a marble piece from Home Depot or another such supplier.

    Regardless of which way you go, I do hope you don't have bursitis in your arm
    RusenBG, Marshal and jseitz like this.
    Our house is as Neil left it- an Aladdins cave of 'stuff'.

    Kim X

  3. #13
    Senior Member
    Join Date
    May 2016
    Location
    Yakima, WA
    Posts
    177
    Thanked: 89

    Default

    I'm with Cuda. When I was researching and finally decided on getting a series of SS for honing, I got the recommendation for a DMT 325 and am glad I got it. Unfortunately, I didn't get the advice about knocking down the highspots with a screw driver shank, so I put in some initial scratches that scared the crap out of me--those problems have since been remedied. Also, if you have any inclination toward working with vintage razors (chip removal, bevel setting, blade correction), and the DMT will be a friend in time of need. Also there is the cost to benefit ratio: overtime, you're going to get more bang for the buck with the DMT. Another benefit to the DMT is that you can use it raise a quick slurry when honing. I'd imagine that the sandpaper would set up would be a little more awkward for that. Either way, you'll have fun and like the 12K SS!

  4. #14
    Senior Member k5MOW's Avatar
    Join Date
    Mar 2014
    Location
    Friendswood TX
    Posts
    313
    Thanked: 36

    Default

    One more question on the 12,000 grit specialty stone. Do they need flatting right out of the box? Do they come flat?

    Roger
    Have a great shave.

    Roger

  5. #15
    Senior Member blabbermouth bluesman7's Avatar
    Join Date
    Jul 2014
    Location
    Denver CO
    Posts
    4,628
    Thanked: 811

    Default

    Quote Originally Posted by k5MOW View Post
    One more question on the 12,000 grit specialty stone. Do they need flatting right out of the box? Do they come flat?

    Roger
    They do need to be lapped a bit out of the box, even if they are flat the surface needs some conditioning.

  6. #16
    Senior Member blabbermouth
    Join Date
    Dec 2014
    Location
    Virginia, USA
    Posts
    2,224
    Thanked: 481

    Default

    Quote Originally Posted by bluesman7 View Post
    They do need to be lapped a bit out of the box, even if they are flat the surface needs some conditioning.
    This. Every hone I have has needed some degree of flattening. Norton, Shapton, Naniwa, I think the one exception were the Welsh slates I got from AJ. He had them pretty well flat and I only needed to condition one side.

    I didn't try the Naniwa or Shapton surfaces to see if they had a similar skim coat of material to Norton hones that needs be done away with to get to the good stuff, but I assume they're better after a little prep and break in. I find that's the case in most every aspect of razor honing. The prep work and break in are the foundations of success.

  7. #17
    Senior Member k5MOW's Avatar
    Join Date
    Mar 2014
    Location
    Friendswood TX
    Posts
    313
    Thanked: 36

    Default

    Thank you all very much for the info. I lapped The specialty stone with 400 grit sandpaper and a piece of glass. Worked great.
    BobH likes this.
    Have a great shave.

    Roger

  8. #18
    Senior Member k5MOW's Avatar
    Join Date
    Mar 2014
    Location
    Friendswood TX
    Posts
    313
    Thanked: 36

    Default

    Thank you all very much for the info. I lapped The specialty stone with 400 grit sandpaper and a piece of glass. Worked great.

    Roger
    captainhx and Butzy like this.
    Have a great shave.

    Roger

  9. #19
    Junior Member Neunerball's Avatar
    Join Date
    Dec 2016
    Location
    Roswell, Ga
    Posts
    24
    Thanked: 0

    Default

    As a newb, I've read a lot of threads. However, there's on thing, that still confuses the hell out of me, which is "Bevel setting". I saw several videos and pictures, showing all the names for all the parts of a straight razor. FYI, English is my second language. Does "Bevel" refer to the sharp edge of the razor blade, or what?

  10. #20
    'with that said' cudarunner's Avatar
    Join Date
    Aug 2010
    Location
    Walla Walla in WA State USA
    Posts
    11,225
    Thanked: 4237

    Default

    Quote Originally Posted by Neunerball View Post
    As a newb, I've read a lot of threads. However, there's on thing, that still confuses the hell out of me, which is "Bevel setting". I saw several videos and pictures, showing all the names for all the parts of a straight razor. FYI, English is my second language. Does "Bevel" refer to the sharp edge of the razor blade, or what?
    Maybe this will help a bit.

    http://straightrazorpalace.com/honin...-you-leap.html
    Our house is as Neil left it- an Aladdins cave of 'stuff'.

    Kim X

Page 2 of 3 FirstFirst 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •