Results 1 to 10 of 12
Thread: Unknown stone any ideas?
-
01-21-2011, 03:08 PM #1
Unknown stone any ideas?
I just got a stone in the mail that I bought off ebay. I rolled the dice and I think I crapped out. It came stuck in a block of wood, so I cut it out. I think the previous owner used oil on it or laquered it into the wood because it is caked with black crap :-/ (anybodys guess) top, bottom, and sides. I tried dial and a wet/dry sanding sponge it with minimal results. Any suggestions on how to clean it up? I'm thinking about using paint thinner on it. Will paint thinner hurt it in any way if it is not a natural stone? Any suggestions on how to proceed would be greatly appreciated.
Anyone have a guess on what it is? Its 7 3/4" X 2 1/8" X 6/8" It gives off a tan slurry, like the dots in the first pic, but it is a B***H to get slurry raised!!! Tons of preasure and like 150 strokes with a small survival knife sharpening stone produced minimal slurry.
Thanks
Louis.Last edited by Louis; 01-22-2011 at 01:29 AM.
-
01-21-2011, 03:37 PM #2
To my untrained, n00b eyes, and given your brief description of its original condition, could that possibly be a Turkish oil stone?
-
The Following User Says Thank You to SonOf1337 For This Useful Post:
Louis (01-23-2011)
-
01-21-2011, 04:56 PM #3
The second photo looks to have some purple in it. If it does and if the stone is greenish gray I would think it might be a Charnley. They are usually longer but the description of being varnished into a block of wood is also typical of them.
Please ease up on the language. We try to keep this board child friendly and we don't tolerate that kind of stuff. Thanks in advance for your cooperation.Be careful how you treat people on your way up, you may meet them again on your way back down.
-
The Following User Says Thank You to JimmyHAD For This Useful Post:
Louis (01-23-2011)
-
01-21-2011, 10:31 PM #4
Poor stone, forcefully removed from his housing that was part of him for so long and about to be placed in paint thinner.
I see lines in the edges, perhaps a Hindostan?
Why do you want to raise slurry?
-
The Following User Says Thank You to Piet For This Useful Post:
Louis (01-23-2011)
-
01-22-2011, 01:34 AM #5
Sorry about the language, its been edited. I will keep this in mind for future posts.
Apoligies
Louis.
-
01-22-2011, 02:51 AM #6
- Join Date
- Apr 2008
- Location
- Essex, UK
- Posts
- 3,816
Thanked: 3164I love that, Piet - very poetical! You have made me feel sorry for the stone, evicted from his house and subjected to a bath of paint thinners.
They wouldn't do that in my country - oh - hold on, they do. Except after being thrown out of your home you aren't thrown into a bath of thinners, just onto the street.
Life is unkind. Then we die.
Regards,
Neil
-
The Following User Says Thank You to Neil Miller For This Useful Post:
Louis (01-23-2011)
-
01-22-2011, 10:34 PM #7
- Join Date
- Mar 2009
- Posts
- 1,211
Thanked: 202My gues would be Hindostan too.
-
The Following User Says Thank You to adrspach For This Useful Post:
Louis (01-23-2011)
-
02-14-2011, 11:04 PM #8
Cleaned and lapped
Well I had some time on my hands yesterday and decided to follow a tip on how to clean the oil off/out of this stone so I put it threw two cycles in the dishwasher. That worked better than my previous attempts. After the stone had cooled off I gave it a light sanding with a hand held belt sander, then I used two sided carpet tape to tape a sheet of 80 grit sandpaper to a 2'X2' board. I sanded it totally flat on both sides, a quick sand on the others, and slightly rounded all the edges to avoid chipping. I'm still not sure what it is, and I'm hoping these photos might help someone in ID-ing it for me. Thanks in advance for the help.
Louis.
-
02-14-2011, 11:26 PM #9
It still looks the most like a Hindostan. Mine is a finisher but not as fine as my Thuringians or CFs, assuming I used it right.
-
The Following User Says Thank You to Piet For This Useful Post:
Louis (02-15-2011)
-
02-15-2011, 12:02 AM #10
I have to agree with Piet. Especially after seeing the sedimentary layers.
It is easier to fool people than to convince them they have been fooled. Twain
-
The Following User Says Thank You to nun2sharp For This Useful Post:
Louis (02-15-2011)