Results 1 to 10 of 10

Hybrid View

  1. #1
    Senior Member InstaRAD's Avatar
    Join Date
    Jan 2010
    Location
    Ontario,CA
    Posts
    242
    Thanked: 40

    Default Recondition a hone?

    Bought a Swaty and it looks in rough shape. There are two areas on the face that you can feel a raised blemish. Also it may have seen oil used on it, how can it be brought back to serviceable condition.

    Pictures to follow.

  2. #2
    Senior Member blabbermouth Hirlau's Avatar
    Join Date
    Dec 2010
    Location
    South Florida
    Posts
    13,530
    Thanked: 3530

    Default

    My two cents;
    I use Simple Green to scrub my hones with. A bio safe, great cleaner & degrease. if the hone is in really bad shape, I use EZ Off Heavy duty oven cleaner for 20 minutes, then scrub with Simple Green.
    If you feel a raised blemish, I would pencil grid it, then gradually lap it until the blemish is gone.
    But, I'm new with hones and I'm sure the guys will be along soon with more ideas.

  3. #3
    Chat room is open Piet's Avatar
    Join Date
    May 2009
    Location
    Rotterdam
    Posts
    937
    Thanked: 229

    Default

    It sounds like it could use a lapping. Swaty's are really hard so make sure to start with coarse sanding paper and work your way up to a fine grit. I'd start with a 120 grit sanding mesh if it's really bad otherwise with 120 waterproof sanding paper.

    I wouldn't worry about the oil, lapping will remove any remnants, I'm not sure if oil can even get into a swaty.

  4. #4
    Senior Member WillN's Avatar
    Join Date
    Jan 2011
    Location
    Lilburn,Ga
    Posts
    286
    Thanked: 94

    Default

    I wouldn't worry much about the oil either. I have read that some hone manufacturers recommended boiling the hone in petroleum jelly.

    EZ off will surely get the oil out and lapping will finish the job.

    Will N.

  5. #5
    Senior Member InstaRAD's Avatar
    Join Date
    Jan 2010
    Location
    Ontario,CA
    Posts
    242
    Thanked: 40

    Default

    Name:  PC221596.jpg
Views: 244
Size:  28.0 KBName:  PC221597.jpg
Views: 240
Size:  28.5 KBName:  PC221604.jpg
Views: 248
Size:  26.3 KBName:  PC221608.jpg
Views: 240
Size:  25.2 KB

  6. #6
    Senior Member mjhammer's Avatar
    Join Date
    Apr 2011
    Location
    Wheat Ridge, Colorado
    Posts
    1,330
    Thanked: 262

    Default

    Nah, that hone isn't in bad shape. The chip is not good, but it's not that bad either.

    I usually don't even bother with cleaning them when they look like this. I simply hit it immediately in a fully submerged sink full of WARM water and my DMT and start lapping. Anything that does not belong to the hone soon will disappear.

    Using a Granite lapping plate and wet or dry will remove a lot of material fast, then take it to even higher grits.

    Most of your worries are on the face anyway, not the back. Don't worry much about the face until you have the back surface nice.

    I usually finish my hones on up to 600grit on the face and 1k or more on the back. That's just how I do it. I learned about using different textures on a single surface hone to add to cutting and polishing effects. It hasn't ever served me wrong.

    It's a beauty!! I had 5 Swaty's, only 3 left now after selling some off. They are wonderful stones, really good polishers. I think you will enjoy this hone for many years to come!

    Good luck mate!

    M
    ​-- Any day I get out of bed, and the first thing out of my mouth is not a groan, that's going to be a good day --

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •