Thread: Issue with honing many razors at once.

Glad im not along here. The pile that needed honed was getting way to big so i dove in. I will take your advice Shaun and keep it at a minimum and test shave before starting another group.

Im going to try some treated stropping to see if i can pull the harshness out of this one when i get the chance. If not, then i will throw the Arkie at it and see what happens.

Nonsense.

One you become a honemeister it's like, er... you know....being superman. Those magic fingers just instinctively know when to stop on each razor and you attain perfection each time.

yes it's all written in the honers bible on page 1026 paragraph 8 line 6.

As to notes, what notes? You don't need no stinkin notes. Superman don't need no notes on how to fly does he?

Seriously, sometimes when you have a pile to do just doing one stage at a time on all of them simplifies the process. Once you have a good bevel on all of them you can then custom finish each one with your best 8K or 12K.

When I'm good enough to do 3 at a time it seems that creating a bevel on all and then moving to the next stage sounds very logical.
Thank you gentlemen, good stuff!

Originally Posted by thebigspendur

Seriously, sometimes when you have a pile to do just doing one stage at a time on all of them simplifies the process. Once you have a good bevel on all of them you can then custom finish each one with your best

^^^^^ This is my process

That is what i do also. I take every blade to the stone untill im done with the stone. This way im not taking the stone out over and over. But somewhere along the way something happened or got missed.

Im really start8ng to enjoy the bevel setting process. Finding one part of the edge that just isnt taking and finding the right trick to get that section to set right. And even after the bevel seems set i will still do a few more light laps just to try and even it all out. Its a lot of fun. The progression of all the other hones is the boaring part. Its just over and over u til you get to the end. Setting the bevel is fun. Until it pisses me off. Then back in the pile it goes till next time.

Ya gotta keep tapping on the magazine, Jerry. Those gattling guns have a tendency to jam if you turn the crank too fast.

Yeah, it's all about that bevel set, really, and I also like to take a group of razors up through my progression together, one stone at a time. I will even still occasionally really max out the bevel set on my beloved Chosera 1k with some ultra-light finishing strokes followed by stropping, and then test shave. I've gotten some great shaves just off that 1k, which just goes to show ya.

I do like Shaun and probably some others do: I'll test-shave 2 (and occasionally even 3) razors at once. I tried keeping a honing log/spreadsheet, but am too lazy to really keep it up (I have to do so much of that for work that I resent doing it in my hobby lol!). I try to remember what I did for any given blade, but as I seem to be mostly finishing on the Nani 12 followed by a fine Arkie progression these days, there's not so much to remember.

There are many roads to sharp. I enjoy hearing about everyone's different routes.

edit: In reading your OP again for detail, it reminds me of my own experience. I too (and I suspect, many other honers) have "finished" a blade to what I thought was an ultra-fine finish honing with your finest "icing on the cake" strokes. Then you go to test shave and get tugging on all or part of the blade. I'm pretty sure that issue nearly always goes back to an imperfectly set bevel. Back to the drawing board, slow is fast, do not pass go, etc.

I used to do 5-10 at a time but it’s just to hard to keep up on so now I just do 3at the most and it’s a lot easier and a lot more rewarding

Since I only hone razors for my own use, I normally hone one at a time, but I have done 4-5 at once when I needed to go through a full progression. It is easier to do it that way than to pull out a full set of hones several times.

Normally, I am refreshing a razor and use only a finishing hone, or perhaps a prefinisher as well. Normally, I will have a shave that is not quite up to standard. I will pull out the finishing hone to touch it up and then shave with the refreshed razor again the next day. It is shaves well, it goes back into rotation. If it still does not pass muster, I will back up to a prefinisher before the final finishing stone. Usually, that will take care of it. If that still does not get the job done, I remove the razort from rotation until I have other razors that need the full progression.