Results 1 to 10 of 20
Hybrid View
-
03-27-2020, 07:17 PM #1
The two others that did this were rehoned by Abrams and Utopian. Same result.
Feeling an edge crumble while you shave is something you don't forget.
One of the two was reheat treated and tempered. It then shaved great. I have not fooled with the third one.If you don't care where you are, you are not lost.
-
03-27-2020, 07:57 PM #2
Yeah, it's a nice WB-I've never seen one that wouldn't hold an edge (well, I did give up on one that the spine was gone and it was flat on both sides-totally hopeless, at least for me). Before I read Randy's post, I wondered the same thing. Maybe stop at 8k like he says, strop and shave? Maybe it won't hold the SG20 edge? And maybe Marty's right about the tang? Frustrating either way.
I guess Glenn's quote applies here: "Honing is easy until it isn't."There are many roads to sharp.
-
03-27-2020, 08:14 PM #3
Dave in my experience some steel can’t take that high grit finisher, good advise to try shaving after starting over and going to 8 k and shave
“ I,m getting the impression that everyone thinks I have TIME to fix their bikes”
-
03-27-2020, 08:33 PM #4
I got mine figured out so keep it up and you will get it. I don't go as high as 20k on a Sheffield blade. Some can take it but I've found if I want more than 8 or 12k on a Sheffield, I go to naturals.
It's just Sharpening, right?
Jerry...
-
03-27-2020, 09:16 PM #5
If nothing else you still have a nice set of scales.
-
03-27-2020, 11:02 PM #6
- Join Date
- Dec 2012
- Location
- Egham, a little town just outside London.
- Posts
- 3,738
- Blog Entries
- 2
Thanked: 1075I will only echo what some others have said that my Sheffields don't take an Gok 20k edge. And if I do it'll only be 5 laps.
-
03-28-2020, 12:10 AM #7
I have a Joseph Elliot 'The Hamburg Ring' that people have told me is a Sheffield. Other than that razor, which holds a great fine edge, I have always thought that all of the Sheffeilds that I've honed were much too soft.
-
03-28-2020, 01:02 PM #8
The tale of woe continues.
Paying careful attention to what Marty and Randy suggested. I went to a 2k stone and started over. After a few strokes a chip appeared. Not just a chip but a chunk. Stayed on the 2k and was working out the the chip when another chip fell out.
To a 325 and breadknifed the blade per Glen's tutorial.
Dropped to a 600 and started to set the bevel. This was going well until another chip appeared.
Then I followed Bouchie's advice and put it away.
I'll keep the scales.
Bummer indeed.If you don't care where you are, you are not lost.
-
03-28-2020, 01:13 PM #9
Definite bummer indeed Dave.
I've felt your pain.
Over the years I've had a couple of razors like that.
I worked for days on them and got no results.
That's what ticks me off the most. I expect results from hard work.
Once in a while you just got to bite the bullet.
Off to the wind chime box it goes!
Pete <:-}"Life is short, Break the Rules. Forgive quickly, Kiss Slowly,
Love truly, Laugh uncontrollably, And never regret ANYTHING
That makes you smile." - Mark Twain
-
03-28-2020, 01:41 PM #10
I'm sorry to hear that. Some old blades have intergranular corrosion, unapparent until well into the honing process.
Seems to me that Glen used to trial month the blade between popsicle sticks with tape to hone long enough to check the consistency of the metal.
RichardBe yourself; everyone else is already taken.
- Oscar Wilde