Results 1 to 10 of 19
-
11-15-2010, 02:23 AM #1
What is your method of honing a new straight?
I'm interested in peoples opinions of how they hone a new straight that comes with a factory edge on it. Do you test the edge and then pick it up in the honing sequence of where you think it sits ie start on perhaps 8k and then move up or do you start from scratch and reset the bevel and then go up the sequence?
-
11-15-2010, 02:51 AM #2
I'll usually go ahead and do a full bevel reset and finish it out how I like it... No muss, no fuss...
-
11-15-2010, 03:01 AM #3
- Join Date
- Jan 2008
- Location
- Rochester, MN
- Posts
- 11,552
- Blog Entries
- 1
Thanked: 3795Agreed. Everything starts at a new bevel. If the razor is already properly honed, then setting a new bevel takes nothing at all to accomplish, so it's not as if it's overkill or taking off excessive steel.
-
11-15-2010, 03:08 AM #4
Seems that I buy mostly vintage razors so they generally start from square one. About all of the new razors I've bought in the last couple of years came shave ready. I bought a set of Heirbert Wacker wedges that I specified that I wanted to hone myself. They came so close that I just went to a coticule and did a bit of finishing on them. If I was to buy a new razor and it needed to be honed it would depend on how close or far it was from shave ready. I would strop and try a shave test first.
Be careful how you treat people on your way up, you may meet them again on your way back down.
-
11-15-2010, 03:55 AM #5
Depends on how you define a factory edge. If its just a primary bevel done with the spine off the stones or similar you have no choice but to set a new bevel but if it's claimed to be shaveready give it the benefit of the doubt & strop & shave test.
The white gleam of swords, not the black ink of books, clears doubts and uncertainties and bleak outlooks.
-
11-15-2010, 05:02 AM #6
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 27,031
- Blog Entries
- 1
Thanked: 13245We are going to sooner or later have to admit that times have changed
Not very long ago the two big companies Dovo and TI put out edges that were not even close...
But more recently they have tried to step up their game, now honestly I don't hone a lot of factory fresh razors right outta the box, Lynn would really be the one to ask...
But the ones that I have honed have been way better then they ever were before...Still not up to most of our standards but at least they are trying now...
Before you had to finish the bevel then hone, now the bevel is at least there it just needs some refinement, but you have to be able to find it and tweak it...
Myself I usually reset a new bevel to make sure...
-
11-15-2010, 05:18 AM #7
- Join Date
- Jan 2008
- Location
- Northern California
- Posts
- 1,301
Thanked: 267I will always look at a new razor's edge and see how it looks and how it cuts the ole arm hair. I almost always go ahead and at least start a shave and if it is not to bad try to finish with it. It is seldom that I like the shave well enough to just let it go and continue using it. I obtained two custom razors and only one had an edge I would keep.
I am with most everyone else I will reset the bevel and go from there. I usually is not that much effort if someone has at least given it a college try to put a bevel on the razor. I am pretty particular though.
Take Care,
Richard
-
11-15-2010, 06:25 AM #8
With new Dovo's, I can typically start at the 5k level. New TI's have needed some work on the 1k to get the bevels properly set.
-
11-15-2010, 07:00 AM #9
- Join Date
- Jun 2010
- Location
- far north
- Posts
- 85
Thanked: 12I have a couple TI's that didn't come shave ready. The TI Luxury wheatfield Le Canadien just needed about 20 laps on 8k and 20 on 12k naniwa and it was good to go.
I started the other TI on the 4k.
I only have one dovo that came fresh from the factory and that was almost shave ready too and I finished on the 8k and 12k
-
11-15-2010, 07:42 AM #10
johnmrson,
As I am still in the newbie phase of honing, I always set a bevel first, so I know I am starting from a stable reference point.
I don't yet have the intuitive skills to look at a factory fresh blade and say, "Nope - that does'nt need a bevel set" !
Have fun !
Best regards
Russ