Thread: First (and second) hone report

Very cool. A little patience and persistence goes a long way. Congrats on your success

Can't wait to hear about the shave!

I can't help wondering if the 5 laps on the 8K after taking the tape off missed the edge because of the resulting decrease in angle.

Ace/David,

Yea, it's a possible consideration.

David,

Well done. Technically, many of my blades sit right where you are probably at, an order of magnatude below a Lynn Abrams honed razor, and below a Glen honed razor, and well, BigSpendur and JimmyHad . . . well, you get the idea. Anyway, they shave great.

But, also consider what would happen if you started applying as much thought, research, and practice into stropping . . .

Also, give some consideration to continuing to learning to hone with one hand. I'm pretty sure that many of the blades we see with bad spine wear come from people who hone with two hands and figured that it wouldn't cause a problem, but 10-20 years later you've got a real problem developing on your spines. It sounds like you weren't pushing into the blade though, good on ya for that.

I probably have no business making comments about what should be done on an 8K or 12K stone because my problem is that I can't there without screwing the blade up in the process.

I can set a bevel, but the problem is that I make a mess of the blade in the process. I can identify a proper bevel by way of the TNT and the appearance of the edge under 30X.
The problem is that my attempt to get rid of the last ugly edge I created results in my breadknifing the edge to get rid of the tall bevel sides I created in the last attempt. Those are the result of uneven and too much pressure, the blade flexing in the process. Instead of a neat, small bevel, I get one that looks like it goes way up the blade. I know that is wrong because I have blades honed by the best. Of course, I don't get near my hones with them. I may be stupid, but I ain't crazy.

Example: I spent the last two evenings, a total of at least 8 hours, setting a bevel. I had breadknifed the edge to get rid of the tall bevels I had created. But the result was that using little or no pressure, even on 80, then 220 grit took FOREVER to get even close to a bevel. By the time I got close, I was literally worn out. My shoulder hurt (surgery ten years ago) and my hand was cramping. As this all went on and on, my accuracy with my stroke decreased and once again I started to apply pressure because I was getting nowhere. Once again I wound up with a bevel but an extremely ugly one. I know what a good bevel should look like. I just cannot for the life of me produce one. I believe that my knowledge and technique would get me a good edge if only I could set a bevel without doing what I've been doing. If I could get to my 4K stone in good shape, I think I could finish the job, but I can't get there without producing a truly ugly bevel. So what am I going to do about it?

1. I'm done breadknifing. The next time I screw up a practice razor, it goes in the trash. I'm done bringing
razors back from breadknifing to a bevel. I have better ways to spend 8 hours making my arm hurt.

2. I have purchased and am waiting for some razors that don't need major work to get sharp (I don't even DARE say shave ready at this point.) They look like they need only a little work at 1K to get a bevel.

3. I'm also SO done at 80 grit. I learned this: if you're at 80 grit, you're already lost.

4. I'm provisionally staying with tape in my attempt to get short bevels. You would not believe what 80 grit will do to the spine of a razor without tape.

5. If I made any typos, I'm sorry but pain pills are tough on my typing.

Thanks for the input. Ace, I had the same thought about pulling the tape.

This razor is a little odd in that the size of the bevel is different on each side. I think the blade has a micro warp. It seems OK when honing the side with the more "normal" width bevel. When honing the side with the skinnier bevel it seems like the toe and heal stick up off the bevel about 1/64". In other words, I can see it but I don't think I can take a picture of it. I've looked at through a loupe (acutally a piece off of some old opera glasses) and the bevels look totally different.

I just got the Wosty I've been waiting for and it is similar shape to what this razor was when it showed up. I'm going to clean it up this weekend and take a shot at honing it and see if my results are differnt. Then I'll go back and rework the KHS. It's a very cool little razor with bolsters. It looks like it was never used. I may have to send it to Glen and see if he can work with it.

More to follow...

--David

Can you post a photo of both bevel sides? I think you're saying one side is wider than the other? If so, this happens, its not going to ruin the edge if its what I'm thinking of.

If the heel and toe are off the hone when you strok then you need to torque (no force!) the blade on a tiny level while x stroking and keeping the blade on the hone to get the whole edge evenly. Hope that helps you.