Page 1 of 2 12 LastLast
Results 1 to 10 of 13
Like Tree1Likes

Thread: Honing Advise - newbee

  1. #1
    Member
    Join Date
    Mar 2012
    Posts
    93
    Thanked: 14

    Thumbs up Honing Advise - newbee

    First I wish to thank Lynn and all the members for there great videos and helpful library here at SRP. I did my first touch up hone this weekend. Thanks to Lynn's advice I used the Naniwa 12000 super stone and flattened it with the DMT 325. I followed the library of instructions for flattening the stone - easily accomplished - and watch all the honing videos. To make a long story short, I spent a long long time working on my Hart Steel 6/8 to bring back the sharpness. This razor was purchased used and was claimed to be new and shave ready. The shave quality deteriorated quickly hence my need to touch up. As a comparison I purchased a used Hart Steel 6/8 from a member here and received an ultra sharp razor. Thus my comparison in sharpness. I got the razor to shave ready with a lot of hone time and I now have a de-haired forearm as proof. Obviously I needed to start one grit back from my 12000. My question - which stone would be the first step with a razor that is hard to touch up? It should be added to my arsenal of hones. Thanks

  2. #2
    ..mama I know we broke the rules... Maxi's Avatar
    Join Date
    Feb 2010
    Location
    Toronto, Ontario, Canada
    Posts
    2,895
    Thanked: 993
    Blog Entries
    8

    Default

    In my experience, an 8K Norton is a good go-to for razors that do not immediately respond to either A) crox or B) a 12k hone.

    However, the next questions:: On a razor that is difficult to touch up, is the bevel properly set? And has this correctly set bevel been properly sharpened and polished? I realize that I'm raising more questions than I'm answering. A razor that shaves properly and smoothly will have had each stage of setting, sharpening, polishing, finishing and stropping applied to it, appropriately.

    Lastly, personal technique plays a monsterous role in the continuance of a shave ready edge. I'm not saying it was you....just laying down the framework for success.

    The short answer....an 8k.

  3. #3
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    Most of these razors that I have seen honed have a micro bevel in them. So, I usually go back to the 1K to re-establish a bevel and then re-hone it and it's good to go. I think if you would just use 5-10 strokes on chromium oxide or .5 diamond depending what has changed since you had the 12K on it, you might be back in business. Worth a try before a total re-honing.

    Have fun.

  4. #4
    Member
    Join Date
    Mar 2012
    Posts
    93
    Thanked: 14

    Default

    Thanks all -

  5. #5
    Eagle-eyed Zephyr's Avatar
    Join Date
    Jan 2011
    Location
    Slemmestad, Norway
    Posts
    1,535
    Thanked: 418

    Default

    IRC the Hart razors have a secondary bevel from the factory as they are using the "Zowada" method, adding two extra layers of tape (a total of three) for the last finisher, this might be the reason for your troubles.

    If you don' succeed with Lynn's advice you can try to put on three layers of tape and take it to the 12K, if it don't help you can take it to a 8K or maybe a 4K to take out the secondary bevel.

    FYI: The one you got from me I took back to 1K and reset the bevel and it got only one single bevel.

  6. #6
    Member
    Join Date
    Mar 2012
    Posts
    93
    Thanked: 14

    Default

    Quote Originally Posted by Zephyr View Post
    IRC the Hart razors have a secondary bevel from the factory as they are using the "Zowada" method, adding two extra layers of tape (a total of three) for the last finisher, this might be the reason for your troubles.

    If you don' succeed with Lynn's advice you can try to put on three layers of tape and take it to the 12K, if it don't help you can take it to a 8K or maybe a 4K to take out the secondary bevel.
    FYI: The one you got from me I took back to 1K and reset the bevel and it got only one single bevel.
    Zephyr thanks - I just finished shaving with both Harts. My honing job was acceptable yours was great. I will try the three layers of tape first. Then I will order a 4,6,or 8 k and take out the secondary. BTW I got mine very sharp on the 12k then finished with Crox balsa strop. Before I went to the 12K I had tried the CroX with no improvement. Now I have a good starting point to get to a great sharpness. All thanks again -

  7. #7
    Senior Member Tim Zowada's Avatar
    Join Date
    Feb 2007
    Location
    Northern Michigan
    Posts
    235
    Thanked: 407

    Default

    Although I no longer consult for Hart Steel, I still know a few things about them... .

    There should not be a micro, or double, bevel on them when they are new. If there is, someone goofed-up. Whether there is a micro bevel, or not, it sounds like your razor needs some attention. Lynn's advice is right on. Although, I usually use a 4000, instead of 1000, as long as the razor has a narrow honing bevel. If you are in a hurry, the 1000 makes things go pretty fast though.

  8. #8
    xuz
    xuz is offline
    Senior Member
    Join Date
    Mar 2012
    Posts
    102
    Thanked: 15

    Default

    Quote Originally Posted by jeffzeitlin View Post
    Zephyr thanks - I just finished shaving with both Harts. My honing job was acceptable yours was great. I will try the three layers of tape first. Then I will order a 4,6,or 8 k and take out the secondary. BTW I got mine very sharp on the 12k then finished with Crox balsa strop. Before I went to the 12K I had tried the CroX with no improvement. Now I have a good starting point to get to a great sharpness. All thanks again -
    Have you considered a 4k/8k Norton or 3k/8k Naniwa combination stones?

  9. #9
    Member
    Join Date
    Mar 2012
    Posts
    93
    Thanked: 14

    Default

    thanks all - its time to by a comb stone - I sure it will be used again and this is not a single occurence.
    sleekandsmooth likes this.

  10. #10
    < Banned User >
    Join Date
    Feb 2011
    Posts
    1,256
    Thanked: 194

    Default

    the combo stones are a great tool. you will not be let down I promise good luck

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •