Results 1 to 6 of 6
  1. #1
    Junior Member
    Join Date
    May 2012
    Posts
    11
    Thanked: 0

    Default Did I wreck my diaSharp?

    I bought a DMT diaSharp 325 to lap flatten a King (800/4000) waterstone I have. The waterstone was slightly bowled. I drew a pencil grid on the 800 side of the King and it took about a hundred medium pressure strokes (with ample water) to flatten it. My diaSharp now has some discoloration that can be seen when looking in the glare of a light. Did I ruin it? or is it detritus? should it be cleaned off?

    and secondly, if the diaSharp is a coating of diamond dust bonded to the plate, what keeps the diamond dust from quickly wearing away after a few lappings?

    Thanks,
    Dave

    Name:  photo.JPG
Views: 232
Size:  145.9 KB

  2. #2
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Unless you have a defective plate I would say no it is fine. The diamond abrasive is in a nickel plated strata , if I understand it correctly, and as long as you were lapping with plenty of water it should be fine. I use a nylon bristle brush to scrub any swarf off. Take a kitchen knife or whatever and do a few strokes through the areas that are worrying you. You should feel the diamonds bite if they are still there.

    Dia sharp recommends a drop or two of dish soap in the water when honing BTW.

  3. #3
    Heat it and beat it Bruno's Avatar
    Join Date
    Nov 2006
    Location
    Belgium
    Posts
    15,142
    Thanked: 5236
    Blog Entries
    10

    Default

    The discoloration is normal. I've had it in various colors.
    The diamonds are set in nickel. Over it's lifetime, the plate will lose some of the diamonds that protrude beyond their neighbors. Generally speaking, the diamonds' lower half will stick deep enough into the nickel. When you rub something against the stone, the pressure will be distributed amon all diamonds, so the pressure on each individual one is very low.

    As long as you don't scrape things over the place with a lot of pressure (like putting your body weight on the tip of a screwdriver and then dragging the tip over the plate) you're not hurting the the plate.
    Til shade is gone, til water is gone, Into the shadow with teeth bared, screaming defiance with the last breath.
    To spit in Sightblinder’s eye on the Last Day

  4. #4
    At Last, my Arm is Complete Again!! tinkersd's Avatar
    Join Date
    Dec 2008
    Posts
    550
    Thanked: 55

    Default

    I have been useing the same DMT 325 grit to level my 4 Norton stones and a couple of PHIGS [12K and one 15K] for 3 years now, and not a Bl*#dy problems yet, so don't worry mate, you've got yourself a great leveling stone there, enjoy!!

    tinkersd

  5. #5
    Senior Member jpcwon's Avatar
    Join Date
    Oct 2012
    Location
    Boston, MA
    Posts
    384
    Thanked: 45

    Default

    Mine is discolored and almost looks "worn-out", but I have been told that it's just being broken in...Hey, it works as good as the day i bought it!!
    -JP-

  6. #6
    Senior Member stingray's Avatar
    Join Date
    Feb 2011
    Location
    Odessa, Texas
    Posts
    259
    Thanked: 40

    Default

    Getting slightly off subject but I have found that 3M Scotchbright works well to clean any stone. It is a plastic scrubbing pad.
    Stingray

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •