Results 1 to 10 of 18
Thread: Anyone have any idea on this?
-
03-10-2010, 01:07 AM #1
Anyone have any idea on this?
My father has asked me to find out what I can on this. I'm not having any real luck with the searches I've run, so I'm hoping someone here was working as a barber when this was out.
I've got full res pics if anyone needs a better look.
Just trying to figure out what I can as far as manufacturer info and what approx year it was made.
-
03-10-2010, 01:08 AM #2
- Join Date
- Aug 2009
- Location
- Des Moines
- Posts
- 8,664
- Blog Entries
- 1
Thanked: 2591mechanical clippers.
I used to get shaves by my friends mother when I was a kid , with one of those. If this thing is not sharp enough.....but I guess you know that already, I have no idea about the maker and year.Last edited by mainaman; 03-10-2010 at 01:11 AM.
Stefan
-
03-10-2010, 01:18 AM #3
knew what they were, the question is manufacturer and date
still works on arm hair (of course I tried), have a feeling they're going to date from around the 50s or 60s (he was born '51, youngest of 4).
-
03-10-2010, 10:59 PM #4
- Join Date
- Feb 2010
- Location
- In the rugged Mountains of Montana
- Posts
- 51
Thanked: 11I had one like it once, used it to trim a beard and it pulled resulting in pain so I gave it away. In a pinch it would work once you get used to it. How tough are you?
-
03-10-2010, 11:23 PM #5Be careful how you treat people on your way up, you may meet them again on your way back down.
-
The Following 2 Users Say Thank You to JimmyHAD For This Useful Post:
nun2sharp (03-15-2010), StubbleBuster (03-11-2010)
-
03-11-2010, 07:00 AM #6
I have three or four pairs of those old hand clippers. When they are in good shape they are a delight to use, most especially for trimming sideburns to length before getting down to the serious work with the straight razor. I use my clipper at least once a week.
Judging by what I see at the flea market, these things were made by companies all over the world. A very good one that I have was made by Oster, but I've also seen real beauties from the French and German companies.
When considering one of these old clippers for purchase, make sure that there is no rust and that there are no broken teeth on either the upper or lower blade. Also, there should be a special spring washer under that top thumb knob. The going rate in my area for a pair of clippers like this is anywhere from 2€ up to 15€ depending on condition, whether it still has the original box and (as in all things) who is doing the selling.
Clippers like this can be easily disassembled for cleaning and/or sharpening. Just be careful not to lose any of the pieces. The blades are simply flat-honed on a series of fine stones (guess what we razor aficionados already have in stock?). When reassembling, apply a droplet of oil to the pivot and then a little oil between the blades and another little bit to the top side of the upper blade where it slides against the body of the clipper. That top screw not only holds the whole thing together, but is also serves as a regulator
-
03-11-2010, 02:36 PM #7
there are a couple broken teeth on it, but it is still sharp enough. I use an electric trimmer to set the length of my sideburns, think this would be a bit awkward to use for that (the first few times anyways).
ignatz:
What year were yours from? I'm guessing there wasn't much market for them in the household level and it was mainly a barber tool.
-
03-11-2010, 06:30 PM #8
I can say in all honesty that I haven't the faintest idea in which year my clipper was manufactured. Had I been lucky enough to find my clippers with the original box and instructions... well, perhaps then I might have a shot at giving you an answer.
The design of these clippers is somewhat "timeless" and this was never the sort of item that underwent major design changes, so that the factories could knock out the same model time after time, year after year without disappointing anyone. I would even suspect that the boxes these clippers came in would only be updated if they began to look too much out of date. These simple, reliable hand clippers had their beginnings in an age before planned obsolescence and shoddy manufacturing processes. They predate the advent of electric-powered clippers - magnetic drive and rotary motor powered - which essentially added power to a proven, working design. The manufacture of similar hand-held clipper models continues right up to today. You can still buy them brand new if you like.
Regarding usage: Yes, definitely for barbers, but also for individual home use. These clippers were also used by groomers and veterinarians for such small animals as dogs, cats, rabbits, etc. and (in somewhat larger versions) for sheep, goats, cows, and so on.
-
03-11-2010, 08:10 PM #9
- Join Date
- Apr 2007
- Location
- St. Paul, MN, USA
- Posts
- 2,401
Thanked: 335I got my first hair cuts from my father with some clippers like that - which had been in my mother's family for at least a generation. Between my fidgeting and the less tham perfectly sharp clippers, they pulled hair something fierce. Until Pa got some electric clippers, hair cuts were no fun at all.
-
03-13-2010, 02:24 AM #10
- Join Date
- Feb 2010
- Location
- Chicago
- Posts
- 42
Thanked: 13Nice old mechanical clippers you have there.
Several years ago I bought one from an antique shop and and had it cleaned and sharpened. I set it out in my shop as a conversation piece and it sat there for about a year doing nothing...until the power went out for 3 hours on a Saturday morning.
Well, not wanting to disappoint anyone I picked them up and did the next 3 haircuts with them . They worked great!!! We all laughed alot in the dark and had a great time, but everyone got their haircuts.
Needless to say, I still keep them around.
-
The Following User Says Thank You to SRC For This Useful Post:
pstrjp (03-22-2010)