Results 1 to 9 of 9
Like Tree1Likes
  • 1 Post By Jaber

Thread: ERN Primus E. Pluribus Unum etching.

  1. #1
    Junior Member Jaber's Avatar
    Join Date
    Jul 2013
    Location
    St. Louis
    Posts
    4
    Thanked: 1

    Default ERN Primus E. Pluribus Unum etching.

    Hello Friends,

    I got this ERN Crown and Sword 3160 EPrimus a few days ago and have been polishing it for days with Maas. I've managed to get most of the crud off with the exception of the few dreaded black pits (hopefully you can see them in the photo). It has the "E. Pluribus Unum Primus" etching on it and my question is, how well will an etching hold up to polishing? If I take it to a buffer with compound do you think the etching will survive or should I keep hand polishing it until the rag isn't black anymore? Thanks for any input!! Love the site!
    Attached Images Attached Images  

  2. #2
    Senior Member blabbermouth 10Pups's Avatar
    Join Date
    Nov 2012
    Location
    Across the street from Mickey Mouse in Calif.
    Posts
    5,320
    Thanked: 1184

    Default

    I have been working on an ERN 1166 etched [ Extra Hollow Ground ] 7/8 for about 2 months now. There are a few threads on this but basically start backwards in your progression of abrasives. The hard part is deciding to stop before you ruin the etch. Also think about how deep whatever your using will go. The etch is not deep at all. I have danced around mine with papers down to 400 but I am staying out of the etch with that. I have gone over it with a shaped wooden sanding tool and some paper to 1500 grit but it is scary. I am to the point of just wanting to take out the scratches from the abrasives and leave the rest of the pits. It's either that or risk losing the etch. I wish now I had settled for just polishing it and will never buy an etched razor again. {probably} LOL
    Good judgment comes from experience, and experience....well that comes from poor judgment.

  3. The Following User Says Thank You to 10Pups For This Useful Post:

    Jaber (07-29-2013)

  4. #3
    Senior Member blabbermouth 10Pups's Avatar
    Join Date
    Nov 2012
    Location
    Across the street from Mickey Mouse in Calif.
    Posts
    5,320
    Thanked: 1184

    Default

    Using a tumbler may be the best way to go,,

    here is 1 place to start reading....http://straightrazorpalace.com/works...mentation.html
    Good judgment comes from experience, and experience....well that comes from poor judgment.

  5. #4
    Junior Member Jaber's Avatar
    Join Date
    Jul 2013
    Location
    St. Louis
    Posts
    4
    Thanked: 1

    Default

    Thanks for the info. The tumbler idea sounds interesting. For now, I think I'm better of just polishing it. I can live with the pits if I can get them close to invisible. BTW I think it's going to be tricky for me to hone, its got a pretty fancy spine and this things as dull as a spoon

  6. #5
    Senior Member Lemur's Avatar
    Join Date
    Jan 2008
    Location
    Sweden, Gotland, Visby
    Posts
    1,888
    Thanked: 222

    Default

    Would love to see more pics of that spine!
    Hur Svenska stålet biter kom låt oss pröfva på.

  7. #6
    Junior Member Jaber's Avatar
    Join Date
    Jul 2013
    Location
    St. Louis
    Posts
    4
    Thanked: 1

    Default

    Here ya go Lemur!Name:  IMG_0196.jpg
Views: 405
Size:  31.4 KB
    Lemur likes this.

  8. #7
    Senior Member blabbermouth 10Pups's Avatar
    Join Date
    Nov 2012
    Location
    Across the street from Mickey Mouse in Calif.
    Posts
    5,320
    Thanked: 1184

    Default

    If you tape it, then it should not harm it. Change the tape a lot. Especially if you have to reset the bevel. If it's that dull you may have to spend some time at the lower grits.

    It IS a nice one !
    Good judgment comes from experience, and experience....well that comes from poor judgment.

  9. #8
    Sinner Saved by Grace Datsots's Avatar
    Join Date
    Jul 2012
    Location
    Corning, CA
    Posts
    598
    Thanked: 133

    Default

    Quote Originally Posted by Jaber View Post
    ...I can live with the pits if I can get them close to invisible...
    Sadly flaws will always be visible to you even once we could never see them. This is mostly due to you remembering them as worse than they are. The tumblers seem like a great option for cleaning out pits. I would rather have some pitting but have saved the etch, a lesson learned the hard way.

    Jonathan

  10. The Following User Says Thank You to Datsots For This Useful Post:

    Jaber (09-05-2013)

  11. #9
    Senior Member Lemur's Avatar
    Join Date
    Jan 2008
    Location
    Sweden, Gotland, Visby
    Posts
    1,888
    Thanked: 222

    Default

    Let us know if there is any issues with the stropping, that back looks a little scary sharp...
    Hur Svenska stålet biter kom låt oss pröfva på.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •