Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: Razor Question

  1. #1
    Junior Member
    Join Date
    May 2013
    Posts
    11
    Thanked: 0

    Default Razor Question

    Since I am a newbie, I would like to have some opinions from season vets. I will not go into any details, so please don't ask. I am enclosing two photos, sorry about the poor quality. The one razor is a 5/8 round point. The other razor is supposed to be a square point razor. I have enclosed a close up of that razor. My question is this, is that a original blade manufactured as a square point, or a round point that was cut to look like a square point? I have been wrong in the past, and I really need to be certain about this. Thanks in advance.
    Attached Images Attached Images  

  2. #2
    Junior Member
    Join Date
    May 2013
    Posts
    11
    Thanked: 0

    Default

    Sorry I'm trying to upload the other picture.

  3. #3
    Junior Member
    Join Date
    May 2013
    Posts
    11
    Thanked: 0

    Default The other picture

    I hope this works
    Attached Images Attached Images  

  4. #4
    Junior Member
    Join Date
    May 2013
    Posts
    11
    Thanked: 0

    Default

    I posted the other picture in a separate thead.

  5. #5
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    I merged your Threads so all the pics are together,, After doing so I can say without a doubt "I can't tell from your pics"

  6. #6
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    How long is the alleged cut blade from heel to point ? How long is the blade that is not cut ? Are they by the same MFG ? I cannot tell from the pix either.

  7. #7
    lz6
    lz6 is offline
    Senior Moderator lz6's Avatar
    Join Date
    Feb 2010
    Location
    California
    Posts
    4,833
    Thanked: 1841

    Default

    Both blades in the second picture appear altered to me as in too short for the scales. I am no expert however.
    Bob

    "God is a Havana smoker. I have seen his gray clouds" Gainsburg

  8. #8
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Quote Originally Posted by lz6 View Post
    Both blades in the second picture appear altered to me as in too short for the scales. I am no expert however.
    A side photo of the blades closed in the scales would help to see if that was the case. OTOH, it wouldn't be definitive even if they appeared short ...... unless it was ridiculously short.

  9. #9
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    Quote Originally Posted by lz6 View Post
    Both blades in the second picture appear altered to me as in too short for the scales. I am no expert however.

    Bob has a good point we can't tell that relationship either, a pic of both razors closed from a high angle so we can see the wedges and the end of the razors would also be a good tell for us...

    The relationship of the Gold Etch is another good tell but we can't see that either

    Basically you are asking for an opinion without giving us enough info to start, and even then it is just going to be an opinion from pics posted on the internet

    Also from the first pic it does look like the point is what we call "Neutered" perhaps that is what is throwing off your perception, this was common practice with spike points back in the old days, and still is ...

    Better Pics !!!!
    Last edited by gssixgun; 08-07-2013 at 06:27 PM.

  10. #10
    There is no charge for Awesomeness Jimbo's Avatar
    Join Date
    Aug 2006
    Location
    Maleny, Australia
    Posts
    7,977
    Thanked: 1587
    Blog Entries
    3

    Default

    Sorry to say that if you want certainty you aint ever going to get it. I guess one way to infer the manufacture/creation would be to measure yours and then try to get data to work out the average length of the hypothesised blade type (I guess in this case Gotta x/8 square points of similar manufacture date), factor in a margin of error, see where yours fits.

    I'd suspect though, just by looking at the pictures, that it would be very marginal to say the least.

    If I could offer some advice, just on a friendly basis, I'd say that I understand and admire your indomitable spirit, but some battles you cannot win. I think this may be one of them. Do yourself and your stress levels a favour, chalk this one up to experience, and try to find the positives: it looks like a nice clean razor, and Gottas are very nice shavers. Whether it has been cut down or not, it will shave just as well.

    Good luck and have fun!

    James.
    <This signature intentionally left blank>

  11. The Following User Says Thank You to Jimbo For This Useful Post:

    Lou8857 (08-08-2013)

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •