Results 1 to 5 of 5
  1. #1
    Senior Member brothers's Avatar
    Join Date
    Feb 2009
    Location
    Oklahoma City
    Posts
    154
    Thanked: 22

    Default Rust pits - is there any point?

    I'd like your advice on whether there's any point in messing around with these blades. I've got a couple of razors that may be worthless. Rust spots appear randomly on the blade, and along the edge. Light, but rust.

    Sanding and polishing helped with the appearance to the naked eye, but under the loupe/microscope, there is still rust in the pits, even along the edge. On both of these razors I removed the bevel, then recreated it about 1/16 higher up on the blade, looking for an area of steel without so many pits, was able to re-establish an almost pit-free shavable edge, but the reality of the situation is that the rusty pits are simply there, lurking close to the edge in some cases, looking very much like rusty swiss cheese under the 'scope.

    Is it time to offer them up on ebay with full disclosure (of course) that they are for decoration only, never for shaving? Or should I just throw them away, in the interest of keeping some unscrupulous person from buying them and reselling them as possible shavers to some unsuspecting victim.

    I could even PIF them on the forums for that matter, as practice blades or scale donors or something. Or, am I overlooking a possible repair that might be worth trying? I'm not inclined to spend a whole lot more time, if it's a hopeless cause.

    I'm very interested in hearing your advice. I've got several other razors that are in far better condition, so this is no loss to me, if I should just get rid of them.

    First and second photos are the Henkels Discovery.
    Third and Fourth photos are the Prosperity.
    Fifth photo shows Henkels on top and Prosperity below.
    Attached Images Attached Images      
    Last edited by brothers; 09-04-2009 at 12:11 PM.

  2. #2
    Senior Member blabbermouth hi_bud_gl's Avatar
    Join Date
    Nov 2005
    Posts
    4,521
    Thanked: 1636

    Default

    i think the best advise can be given if we can see the picture. I do really appreciate your honest not to sell razor as far you know it has problems.
    So far if you honed up blade and took all rust out but you still see the rust or cheese edge then you can try a little more (i know you don't want to spend any more time) then see. Or the best way some honing learning people will get great benefit from it.

  3. #3
    Senior Member brothers's Avatar
    Join Date
    Feb 2009
    Location
    Oklahoma City
    Posts
    154
    Thanked: 22

    Default

    Photos have been added.

  4. #4
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    IMO pitting above the bevel is a cosmetic issue. At least until you get enough use and wear to get to the point that the pitting it finally getting into the bevel through honing.

    Once the pitting is in the bevel all you can do is see if you can hone through it to good steel. If it is too deep for that then as you mentioned you'll have that swiss cheese bevel and the razor is a display only piece or a box opener. Good luck with them.
    Be careful how you treat people on your way up, you may meet them again on your way back down.

  5. #5
    Senior Member blabbermouth hi_bud_gl's Avatar
    Join Date
    Nov 2005
    Posts
    4,521
    Thanked: 1636

    Default

    Jimmy is right about the pittings on the edge. Now i think from pictures bottom razor is ok. Again this is what i see.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •