Results 1 to 9 of 9
  1. #1
    Member
    Join Date
    Jan 2011
    Posts
    78
    Thanked: 43

    Default how much rust is too much to salvage

    I have to opportunity to pick up an old old old looking Boker. Can see the Boker stamp and tree, scales are surprisingly ok, but the only problem is it is loaded with rust. I can see that there was once something etched into the blade, but can not tell what it is. My question is - is a rust bucket like this a reasonable candidate for later restoration?

    I am sorry that I can provide pics, but I'm just curious if someone could direct me to a thread that can show me the varying degrees of rust and how much can be done with them. Thanks for any advice.

  2. #2
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    The rust you see means nothing, it is what lies beneath that wrecks the razor, unfortunately you will never know until you start the work
    Last edited by gssixgun; 01-15-2011 at 05:02 AM.

  3. The Following User Says Thank You to gssixgun For This Useful Post:

    smreno77 (01-15-2011)

  4. #3
    what Dad calls me nun2sharp's Avatar
    Join Date
    Feb 2008
    Location
    Kansas city area USA
    Posts
    9,172
    Thanked: 1677

    Default

    If it is free, you might as well chance it. If money is involved leave the razor alone.
    It is easier to fool people than to convince them they have been fooled. Twain

  5. #4
    Member
    Join Date
    Jan 2011
    Posts
    78
    Thanked: 43

    Default

    Thanks for the quick reply. Yeah... that's what I was afraid of. My (limited) understanding is that pitting is the real enemy and will need to be sanded out or otherwise removed. Just may take the plunge and see what happens. Won't set me back very much at all, and may be a great little starter project - because if I lose it - then I lose it... or I can send it out for professional help after I've had a good go at it. Just looking to get my feet wet with fixin' up an oldy-but-goody.

  6. #5
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    There are a few ways you can approach this, and it really depends on what you want. If you want a pretty razor, then this might not be a good candidate as it might not be able to survive pitting removal. On the other hand, if you just want a shaver, then you can either clean off surface rust and leave the pits, or you can even leave the rust and simply hone it and use it as is. Pits anywhere other than in the bevel have no impact on the quality of the shave, only the aesthetics.

  7. #6
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    This razor is a good indicator of what I mean, this Imp looked really bad on the surface, but underneath was a surprise... It also goes the other way too, I just did a Filarmonica #14 that looked to only have water spots until I buffed it and found pitting under there that had to be fixed...


    http://straightrazorpalace.com/works...e-attempt.html
    Last edited by gssixgun; 01-15-2011 at 11:35 AM.

  8. #7
    Senior Member janivar123's Avatar
    Join Date
    Oct 2009
    Location
    Porsgrunn Norway
    Posts
    883
    Thanked: 173

    Default

    Is most of the rust on the part of the blade that is covered when closed?
    If it is there may be the additional problem of celluloid rot witch would mean that the scales need to be disposed of.

    It may not be the case on that razor but it just came to mind when you mentioned rusted blade

  9. #8
    The Hurdy Gurdy Man thebigspendur's Avatar
    Join Date
    May 2005
    Location
    New Mexico
    Posts
    32,736
    Thanked: 5016
    Blog Entries
    4

    Default

    As an experiment I once took a razor and put it in water and left it for a couple of weeks. When I took it out it was covered in rust, totally. It looked like junk. About 1 minute on a dremel and it was brand new looking.
    No matter how many men you kill you can't kill your successor-Emperor Nero

  10. #9
    Member
    Join Date
    Jan 2011
    Posts
    78
    Thanked: 43

    Default

    Thanks for the link Glen. I'm in about the same spot with the Boker - but more rust present on the tang on both sides of the pivot point and more hone wear . I do have a question for all the historians out there... there is etching on the blade that appears to read "Durrian" or "Dorrian" or "Purrian" or something. Does anyone know what this is, or is is potentially custom etching for the original owner?

    For reference, the coffin/case/box says "H. Boker and Co./Unrivaled Razor" and the stamp appears to date from the 1900-1924 era or possibly earlier* as the mark is slightly worn, if that is of any help identifying the etching.

    I'll hit up the hardware store tomorrow or Monday and get cracking. Fun times!

    *age according to the following link - http://www.boker.de/pdf/knifeworld.pdf
    Last edited by smreno77; 01-16-2011 at 03:44 AM. Reason: link provided

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •