Search:
Type: Posts; User: carrolljc; Keyword(s):
Search: Search took 0.00 seconds.
-
06-15-2014, 04:48 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
Looks good. I didn't know about cork sanding...
Looks good. I didn't know about cork sanding blocks. I looked them up on Amazon and just ordered a couple.
Joe -
06-15-2014, 04:10 AM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
I did some hand sanding using the foam pads. They...
I did some hand sanding using the foam pads. They work great!Thanks for that tip.
While sanding the spine, with the blade edge set vertically on the foam surface, I had thought the foam might... -
05-29-2014, 11:46 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
I found a use for it! I clamped a razor in it...
I found a use for it! I clamped a razor in it while pinning the razor. The wedge end of this particular razor is narrow and tight. It was hard to keep the scales open enough to insert washers on the...
-
05-28-2014, 11:31 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
Some good razors have some pits. Sometimes, you...
Some good razors have some pits. Sometimes, you have to choose to leave some slight pitting rather than go down all the way to take out a pin prick here or there. I did that with this blade. Here are...
-
05-28-2014, 11:14 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
While I was building a sanding jig, I also...
While I was building a sanding jig, I also attached a vise to a plank that I could clamp to a work table. I had envisioned holding a blade in the vise and working on it with a Dremel. I did try that,...
-
05-28-2014, 09:59 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
Speaking of hand sanding razors, I tried using...
Speaking of hand sanding razors, I tried using the Dremel attachments identified as abrasive buffs. They look like small synthetic scouring pads.
167792
They're rated at 180, 280, and 320... -
05-28-2014, 09:43 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
I'm hoping for another good effect from the foam...
I'm hoping for another good effect from the foam (besides protecting fingers). When I'm sanding the spine, I hold the razor with the edge directly at 90 degrees on the plexiglass or on the wooden...
-
05-28-2014, 09:27 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
I did go ahead and order some foam. I'll try it...
I did go ahead and order some foam. I'll try it out when it arrives.
Joe -
05-28-2014, 04:51 PM
Thread: Modifying a sanding jig
by carrolljc- Replies
- 16
- Views
- 1,850
Modifying a sanding jig
On another thread a few days ago, I posted pictures of a new work table with a sanding jig clamped to it. After working with the jig, I realized that it contained a basic design error. The backing...
Results 1 to 9 of 9