Search:
Type: Posts; User: DZEC; Keyword(s):
Search: Search took 0.01 seconds.
-
07-25-2019, 01:15 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Don’t know. Wouldn’t hurt to try.
Don’t know. Wouldn’t hurt to try.
-
06-16-2018, 05:37 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Thank you for the compliment. It was rude of me...
Thank you for the compliment. It was rude of me not to respond right away.
I have to admit to being intimidated by the possibility of celluloid rot. The staining on the scales and the black on... -
06-16-2018, 02:50 AM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Breadknifed the blade an an DMT 325 to remove...
Breadknifed the blade an an DMT 325 to remove most of the chip. Then went to an DMT 1000 with 1 layer of tape to set the bevel and finish removing the remnants of the chip. Followed with Norton...
-
06-15-2018, 09:19 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
I got rid of the chip without losing too much...
I got rid of the chip without losing too much metal.
290873
Managed to clean it up and not damage the etching.
290876
The scales cleaned up nicely with toothpaste and automotive rubbing... -
06-03-2018, 11:43 AM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Been on a bit of an extended holiday with wife...
Been on a bit of an extended holiday with wife and dogs and haven’t been able to work on the PUMA as a result. I will get back to it in a week.
I am ordering some replacement horn scales from... -
05-24-2018, 05:08 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Gssixgun to the rescue again. :bow ...
Gssixgun to the rescue again. :bow
Transferring inlays to new scales. I believe Glen glues these to the surface and if that’s OK for him, it is more than fine for me.
... -
05-24-2018, 04:56 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
I found this thread about using heat on plastic...
I found this thread about using heat on plastic to place the inlay.
https://straightrazorpalace.com/workshop/115222-inlays-acrylic-plastic.html
Seems worth a try. -
05-24-2018, 04:36 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Less than 36 hours in a Ziplock and the black...
Less than 36 hours in a Ziplock and the black stuff has reappeared. Sure looks like celluloid rot. Thank you to Cudarunner and others for the warning and the diagnostic suggestion. :cry:
What a... -
05-23-2018, 10:04 AM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Will do. Thanks for the suggestion.
Will do. Thanks for the suggestion.
-
05-23-2018, 01:36 AM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
I used my Dremel abrasive pads on the black...
I used my Dremel abrasive pads on the black stuff. Turns out it wasn’t corrosion after all, just some kind of stain that seems to come off fairly easily. I guess I lucked out on that.
I will... -
05-22-2018, 04:34 PM
Thread: Restoring a PUMA
by DZEC- Replies
- 25
- Views
- 2,847
Restoring a PUMA
Got the coffin box and the razor for $25 CDN. I Will try to clean up the scales and make the razor shave ready, but am asking for some advice before I start.
I will go through the usual steps to...
Results 1 to 11 of 11