Search:
Type: Posts; User: STF; Keyword(s):
Search: Search took 0.01 seconds.
-
01-26-2021, 04:07 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
It might look like the toe but both chips are in...
It might look like the toe but both chips are in about the first 3/4" of the heel
-
01-26-2021, 03:10 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Nor me although it is very hard to see with the...
Nor me although it is very hard to see with the naked eye.
-
01-26-2021, 03:09 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
My feelings aren't hurt Jerry, much :cry: ...
My feelings aren't hurt Jerry, much :cry:
Seriously though, you are right, that is one ugly scratch pattern, I'm quite proud of it actually, bet you can't make one that bad :rofl2:
I do agree... -
01-24-2021, 07:37 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
I have to apologize for my post yesterday, I was...
I have to apologize for my post yesterday, I was on the point of blowing a fuse with this Titan.
Titan aren't problem razors as far as I know, they're not the best but I do know of someone here... -
01-23-2021, 08:38 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Hello again, I read the content about honing...
Hello again,
I read the content about honing on your site and your advice in this thread.
I drew round a coin and ground to the line on a 400 diamond plate (it came today).
As I was... -
01-22-2021, 05:25 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Thanks for the useful information, My Titan...
Thanks for the useful information,
My Titan did shave and pretty well, if it were one of my usual vintage razors i might say it felt like it needed a bit of a refresh but considering that I... -
01-22-2021, 03:12 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
I have another quick question about diamond...
I have another quick question about diamond plates.
How should I use it, dry, water, oil? -
01-22-2021, 11:50 AM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
I just ordered a cheap diamond plate. I don't use...
I just ordered a cheap diamond plate. I don't use the 220 side of my Norton 220/1k but I still don't like that I gouged it so deeply on just one stabilizer.
-
01-22-2021, 11:45 AM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Just ordered one, not from chefs knives to go and...
Just ordered one, not from chefs knives to go and cost me a few more bucks, 400/1K
-
01-21-2021, 06:28 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Thanks, I see what your'e talking about. I'll do...
Thanks, I see what your'e talking about. I'll do it again more carefully.
On a side note, I just had a shave with it. I won't pretend it was the sharpest razor I've used. Not even the sharpest I... -
01-21-2021, 04:38 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
What's a layout line?
What's a layout line?
-
01-21-2021, 04:36 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Ha, Just opened my razor to show my wife how...
Ha, Just opened my razor to show my wife how well I had managed to hone it and let if close on my finger.
328927 -
01-21-2021, 04:16 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
First I have to thank Euclid440 for the thread...
First I have to thank Euclid440 for the thread about correcting stabilizers, Planeden gave me the thread and I did read it but it went straight over my head unfortunately.
Thank you Paul for... -
01-21-2021, 03:44 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Thanks, I just corrected the stabilizer as Paul...
Thanks, I just corrected the stabilizer as Paul suggested earlier with a penny ( 10c actually).
I corrected it with the 220 and you are right about the stones being soft. Talk about deep gouges in... -
01-21-2021, 03:23 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
A quick question. Is a 1K Diamond plate better...
A quick question.
Is a 1K Diamond plate better than a 1K stone, Norton 1K in my case?
If a Diamond plate is better, why is that apart from the fact that it's got diamond in the name so if I get... -
01-21-2021, 11:33 AM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
I have a Norton 1k/220. I haven't ever used...
I have a Norton 1k/220.
I haven't ever used the 220 side obviously but I wonder if it would do the stabilizer grinding/re-profiling that has been suggested and explained so clearly by PaulFLUS.
... -
01-20-2021, 09:46 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Thanks Mike, I haven't actually honed the...
Thanks Mike,
I haven't actually honed the stabilizer, I did that with a dremel.
I read the post that Planeden sent the link for but to be honest I couldn't see what my problem is.
I don't... -
01-20-2021, 03:54 PM
Thread: Stabilizer correction
by STF- Replies
- 64
- Views
- 6,603
Stabilizer correction
Hi Guys,
Although I have read that this subject is in the Library, I can't find it so I am hoping for a bit of idiot proof advice.
I have a razor, it's not expensive but that's besides the...
Results 1 to 18 of 18