Results 1 to 10 of 13
Thread: Cleaning Super Speeds
Hybrid View
-
05-14-2010, 07:51 AM #1
Hi,
If you have access to an ultrasonic bath, then that is the way to go.
Soak razor overnight in 10% solution of liquid dish-washing detergent, then sonicate in the detergent solution for about ten minutes.
Rinse and repeat if necessary. This will get the surface cruft off.
After drying, you may want to lubricate the threads of the turning screw.
WRT the polishing etc, I use a small amount of MAAS, and use it very gently.
Have fun !
Best regards
Russ
-
The Following User Says Thank You to PhatMan For This Useful Post:
d. m. ellington (05-23-2010)
-
05-14-2010, 11:07 AM #2
Cleaning Super Speeds
Hello, d.m. ellington:
I have cleaned a number of these Gillettes. Mine were from rummage sales and flea markets, and they looked as if dragged out a swamp.
First, I soaked them in warm water and vinegar; then gave them a bath in dish soap and water, scrubbing them with an old toothbrush. A touch of Moss shined them up. Finally, another soap and water bath and a towel and an air drying gave me almost new razors.
Regards,
Obie
-
The Following User Says Thank You to Obie For This Useful Post:
d. m. ellington (05-23-2010)
-
05-23-2010, 02:59 PM #3
- Join Date
- Apr 2010
- Location
- Wales
- Posts
- 133
Thanked: 9The same as above, scrubbing bubbles though here in the uk something similar and a good bush with a toothpaste, then a good polish and the results are usually first class.
-
The Following User Says Thank You to technika1 For This Useful Post:
d. m. ellington (05-23-2010)
-
05-23-2010, 04:59 PM #4
+1 for all that has been said here.
If you are using any abrasive metal polish with old DE razors, use it very mildly. The nickel (or gold) plating is very thin; with too aggressive cleaning you might wipe it out.
If that happens or if the plating was already worn, it is possible to get it plated again, but not very cheap. Also taking DE's like Super Speed, Fat Boy or Valet into peaces before plating might be difficult.'That is what i do. I drink and i know things'
-Tyrion Lannister.
-
06-05-2010, 06:15 PM #5
- Join Date
- May 2010
- Location
- Lubbock, TX
- Posts
- 28
Thanked: 6
-
06-05-2010, 06:25 PM #6
-
The Following User Says Thank You to Obie For This Useful Post:
RaiderShaver (06-05-2010)
-
06-05-2010, 08:31 PM #7
- Join Date
- May 2010
- Location
- Lubbock, TX
- Posts
- 28
Thanked: 6Thanks
Thank you for the help. I'm cleaning up my grandfather's old de razor today. It was just given to me. I'll have to get some metal polish to finish it off. Thanks again.
-
The Following User Says Thank You to RaiderShaver For This Useful Post:
Obie (06-05-2010)
-
09-03-2010, 01:44 AM #8
I soak them in a simple green/water solution for 30 mins or so - then brush them with an old electric toothbrush.
Rinse them off and let them dry. Then I soak them for a few mins in mineral oil just to lube the moving parts (if there are any).
No need for polish - the simple green and toothbrush do a wonderful job on their own.
-
09-09-2010, 03:55 PM #9
- Join Date
- May 2010
- Posts
- 109
Thanked: 24Is there a way to disassemble a Gillette DE to clean it? I thought there were instructions somewhere on how to do this.
Thanks,
RB
-
09-09-2010, 10:57 PM #10
Don't make the mistake I once made. I had a Mercur Futur and I soaked it in a strong bleech solution for a few hours. When I took it out most of the plating was gone and it was full of rust. It went straight into the garbage.
No matter how many men you kill you can't kill your successor-Emperor Nero