Page 1 of 2 12 LastLast
Results 1 to 10 of 18
Like Tree24Likes

Thread: Testing a razors sharpness.

  1. #1
    Junior Member
    Join Date
    Feb 2015
    Location
    Oklahoma
    Posts
    5
    Thanked: 0

    Default Testing a razors sharpness.

    Disappointed in my first attempt with a straight razor.
    I have numerous straight razors that I have collected over the years. I decided that with the high cost of safety razor blade replacement, it was time to put these razors to good use.
    I purchased a Norton 4000/8000, and a flattening stone, after watching numerous videos on the subject by Lynn Abrams and others. I spent a lot of time, slowly and meticulously honing a 5/8 Beau Brummel Werk, a 6/8 DD Pearlduck Goldenedge, and a 5/8 Solingen Tuesday using both sides of my new stone. Then stropped each to the point that arm hair was no contest for any of them.
    I prepped for a shave by showering first, shaving oil second, heavy lather third. The Beau was my first choice due to the comfortable feel it has in my hand. I was able to shave both sides of my face from the sideburn to the jaw line, and my cheeks down to my chin. However, when I moved to my neck the razor would not cut. The blade would hang on my beard and lift the skin on my neck. I tried my chin area next, but it was over. It just would not glide. I moved on to each of the other razors, only to find the same scenario. I used short deliberate strokes. The spline approximately a 1/4" off the skin. It started out good, but that was it.
    Any suggestions ?


    Thanks in advance,
    OneFunMudder

  2. #2
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,384
    Thanked: 4820

    Default

    Well I have no specific answer, however there are a lot of experienced shavers in your area that you could meet with. It is never a good plan to try to learn to use a straight and sharpen it at the same time. You have way too many variables to even know where to start. I would suggest that you get a couple of blades pro honed and or meet with an experienced member to go over shaving and stropping. Work out the bugs of your honing after you know the rest of the essentials.
    It's not what you know, it's who you take fishing!

  3. #3
    Senior Member blabbermouth Chevhead's Avatar
    Join Date
    Feb 2013
    Location
    Upstate, New York
    Posts
    2,751
    Thanked: 708
    Blog Entries
    4

    Default

    +1 to what RezDog Said...

  4. The Following User Says Thank You to Chevhead For This Useful Post:

    RezDog (02-23-2015)

  5. #4
    Senior Member blabbermouth
    Join Date
    Jun 2013
    Location
    Pompano Beach, FL
    Posts
    4,014
    Thanked: 631

    Default

    Rezdog is right. There are many variables. For one you may have set the bevel wrong and the edge was too fine so it rolled or bent under pressure. Facial hair is very different from arm hair. Lay the edge flat on your thumb nail and pull it across. Does the edge flex? As far as testing sharpness. My wife has very fine hair. I use a hair from her hair brush for a hht. Not foolproof bet better than arm hair.

  6. #5
    Senior Member blabbermouth Haroldg48's Avatar
    Join Date
    Jun 2013
    Location
    Clayton, NC USA
    Posts
    3,341
    Thanked: 866

    Default

    You took the right test...shaving. Nothing else really is definitive. Is there a chance your lather just dried out too much?
    Just call me Harold
    ---------------------------
    A bad day at the beach is better than a good day at work!

  7. #6
    Senior Member feltspanky's Avatar
    Join Date
    Jul 2014
    Location
    Kentucky
    Posts
    707
    Thanked: 92

    Default

    When you attempted to shave your neck were you going WTG. When shaving your neck, tilt your head back and stretch your skin. Skin stretching turns a ho-hum shave into a great one.

  8. #7
    Senior Member Mephisto's Avatar
    Join Date
    Feb 2012
    Location
    NC
    Posts
    1,408
    Thanked: 126

    Default

    I'll echo what others said, honing and skin stretching. Also, the chin and the neck are difficult areas to shave. You can always get one of your razor honed by someone else as a measuring stick for future honing endeavors.
    OneFunMudder likes this.
    From their stillness came their non-action...Doing-nothing was accompanied by the feeling of satisfaction, anxieties and troubles find no place

  9. #8
    Senior Member jfleming9232's Avatar
    Join Date
    Jun 2010
    Location
    Andalusia, Alabama
    Posts
    577
    Thanked: 125

    Default

    As has already been mentioned, send out a razor to be professionally honed. It's hard to hone if you don't know what truly shave ready edge is. Eliminate as many variables as possible.
    Last night, I shot an elephant in my pajamas..........

  10. #9
    Junior Member
    Join Date
    Feb 2015
    Location
    Oklahoma
    Posts
    5
    Thanked: 0

    Default

    Yes, I had to keep dampening is some and work it around a bit. But, there seem to be excessive drag.

  11. #10
    Junior Member
    Join Date
    Feb 2015
    Location
    Oklahoma
    Posts
    5
    Thanked: 0

    Default

    Yes, WTG, Skin pulled firmly.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •