Page 1 of 2 12 LastLast
Results 1 to 10 of 18
  1. #1
    Junior Member
    Join Date
    Mar 2008
    Posts
    2
    Thanked: 0

    Default Problems shaving against the grain

    Hi,

    I have been shaving with a straight razor about a year now, only with the grain and across it. I have had no problem and get a very good, comfortable shave. A few days ago I tried going against the grain and it was not fun. I started bleeding at quite a few hair folicles and my whole neck and under my chin felt like it was on fire. I seemed to get my cheeks, sould patch area and moustache OK, but under my chin and my neck area was not. Does going against the grain just take some getting used to or am I doing something wrong?

    Thanks,
    Joe

  2. #2
    Senior Member blabbermouth hi_bud_gl's Avatar
    Join Date
    Nov 2005
    Posts
    4,521
    Thanked: 1636

    Default agains the

    prepare your face pretty good +soap (depends on it too) + how sharp is blade.
    +get used to it(your fase.)
    if i won't shave against grain i will not like my shaving.try check your blade sharpness first then soap then try to shave small surface are first then slowly you can increase it.see it cuts blood etc.hope this helps.

  3. #3
    Senior Member Lt.Arclight's Avatar
    Join Date
    Aug 2008
    Location
    New Jerseystan
    Posts
    559
    Thanked: 111

    Default

    I honestly think, that even after years of experience, there are areas on my face that just will not tolerate-ATG. Depending on how the hair is growing,sometimes the angles are so extreme that ATG creates irritation.

    That said, prep is crucial as is a VERY keen edge. I found that if repeated passes are necessary, it usually results in razor burn

  4. #4
    Senior Member sensei_kyle's Avatar
    Join Date
    May 2005
    Location
    Oklahoma City, OK
    Posts
    1,580
    Thanked: 55

    Default

    Going against the grain is tough, but rewarding. Prep and a sharp (and I do mean SHARP) razor are keys. Always save against the grain for last. You might try stropping before the against the grain pass. It might (or might not) help. Also, really stretching the skin taught is very important. You might experiment with differing your attack angle also, probably shallower.

  5. #5
    Face nicker RichZ's Avatar
    Join Date
    May 2005
    Location
    New York, NY
    Posts
    4,178
    Thanked: 32

    Default

    It takes a while for your skin to get used to it.

  6. #6
    Senior Member fpessanha's Avatar
    Join Date
    Feb 2008
    Location
    Coimbra, Portugal
    Posts
    751
    Thanked: 134

    Default

    I, for one, have tried it only once and gave up while I was at it... the blade was sharp, stropped before the ATG pass, the skin was taught, you name it... but the angles are awkward for me and my skin just cannot bare the stress the ATG pass puts on it. Therefore I decided, for the time being, not to do the ATG pass... I find that BBS all over is not rewarding if your face burns like hell. I do some tricks, however, when I go for the XTG pass: I go XTG but, in places, in a upward moving direction. I find that this is almost ATG but the slicing motion (carefuly done, of course...) is an improvement on my XTG pass and makes the ATG, for me, redundant...
    Hope this helps. Not all of us were cut (pun intended...) for the ATG pass...

  7. #7
    Vintage Scent shop clerk Leon's Avatar
    Join Date
    May 2007
    Location
    Porto, Portugal
    Posts
    1,023
    Thanked: 621

    Default

    Quote Originally Posted by fpessanha View Post
    I do some tricks, however, when I go for the XTG pass: I go XTG but, in places, in a upward moving direction. I find that this is almost ATG but the slicing motion (carefuly done, of course...) is an improvement on my XTG pass and makes the ATG, for me, redundant...
    Being not able to do a ATG pass, I also do the XTG pass fpessanha describes.
    It works well by not going completely against the grain, thus saving us from the discomfort of a full ATG pass.

  8. #8
    Never a dull moment hoglahoo's Avatar
    Join Date
    Feb 2008
    Location
    Tulsa, OK
    Posts
    8,922
    Thanked: 1501
    Blog Entries
    1

    Default

    I have to adjust my shaving angle against the skin and the angle of my blade through the stroke in order to shave against the grain. Simply shaving the opposite direction just as I would with the grain results in pain and suffering.

    For me, it's almost a completely different shave independent of the other passes I've already made. It requires different prep, different techniques, and sometimes stropping again to bring back that keen edge if my initial stropping that morning proved insufficient for shaving against the grain comfortably. It was a lot of practice for me, and I still have a long way to go shaving my neck against the grain.

    So, I keep practicing, experimenting, refining, and discovering in my quest for the both close and comfortable shave that I will call complete
    Find me on SRP's official chat in ##srp on Freenode. Link is at top of SRP's homepage

  9. #9
    Senior Member Sharp&Shiny's Avatar
    Join Date
    Mar 2007
    Location
    Basingstoke England
    Posts
    1,027
    Thanked: 112

    Default

    I have finally got good results going ATG by using a light touch & a very shallow angle ,in some places the blade is virtually flat on my face & dont forget to stretch the skin a little.After a while you will find what works for you in regard to your own beard growth.Also I use a very light touch & very little pressure. Hope this Helps .Paul

  10. #10
    Senior Member sensei_kyle's Avatar
    Join Date
    May 2005
    Location
    Oklahoma City, OK
    Posts
    1,580
    Thanked: 55

    Default

    You can also stretch the skin in front of the cutting edge, instead of from behind it. I have found this helps pull the hairs up and makes cutting them a little easier. HOWEVER, stretching in front of the cutting edge is dangerous and may not be for everyone.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •