Results 1 to 10 of 17
-
03-17-2006, 10:33 PM #1
New shaving issues after second shave
Ok, after my second shave I encountered the following issues...any ideas???
1. I noticed that going against the grain on my upper lip I seemed to have peeled off little bits of skin, at first it looked like I missed hairs, but its skin. I am thinking that I may have to much of an angle on the blade, but not sure if that is the issue
2. When shaving against the grain right directly under, on, and directly above my jaw line, the blade tends to skip over patches of skin, like a rock skipping on the water. I am trying to stretch the skin as tightly as possible, but it doesnt seem to be helping
3. I cannot find a good way to reach the area of my neck below my chin going cross grain!
4. I noticed that today my chin area was very irritated, Im not sure if it was using the new TI razor (sharpened by Lynn), or if it was just to soon to shave again against the grain, although I did wait two days, but my beard does not grow fast at all.
I did notice that my first shave was much more comfortable, and the only differences:
First Shave:
Cattaraugus(honed by Lynn)
AOS Shaving Oil
Classic Shaving soap
AOS After shave
Second Shave:
TI Evide (first time using this razor, it was also honed by Lynn)
AOS Shaving Oil
GFT Coconut oil shaving creme sample
AOS After shave (ran out of aftershave so didnt use much)
On the second shave I took a long hot shower (which I didnt do on the first shave since I was so excited to use the razor), but because my beard was so thin and so short from just shaving two days before (and I was in a rush), I started shaving cross grain instead of with the grain. This was never a problem for me with the DE if my growth was minimal, would that change with a straight?
Any help would be GREAT! I am hoping the difference isnt with the razors, because I will only be travelling with the TI, which means I will use it about 60 - 70% of the time.
-
03-17-2006, 11:20 PM #2
JL,
1 - It could have been the angle, I have a mustache so no
experience shaving there.
3 - If you are talking about getting the razor in the right position
to shave cross grain here is what I do. I extend the outward,
so it's like an open knife. I remember another forum member,
I believe AFDavis said he did this.
4 - Is there anyway that the angle could have not been right
or that you used a little too much pressure?
As far as the prep goes I'm sure that it probably wasn't an issue.
It's interesting though that the shave before the shower was
better than the one afterward. I get just a good of a shave from
just washing my face.
Wish I could have offered more.
Good Luck,
Terry
-
03-17-2006, 11:34 PM #3
1. Get a very good pass down and across in both directions and you'll minimise that. I also go extra gently to avoid just the problem you express and go at a very acute angle, almost flat against my lip.
2. Try using a slight cutting angle (carefully of course). That's leading with the tip slightly 5º-30º. there should be less catching up that way.
3. Thats a tough spot for me too. I reach over my head and stretch that way while turning the razor so that the tip aims at my throat and the heel sticks out from my chin. I also turn the scales in to 45º and go at my adam's apple a little closer that way.
4. It's still early days and your skin will need to adjust. You may have been applying some pressure. There really is no pressure needed with a sharp razor. It cold also be less efficient prep, but it sounds like you had that covered.
X
-
03-18-2006, 12:04 AM #4
Well, I did tell you not to shave against the grain . . . so its skin. You've probably noticed there isn't any safety bar on a straight, with the grain it goes as deep as you push it. Against the grain it catches on hair and goes deeper than it should. Thus, skin gone, beard too though huh? LOL...
Its the razors, there different. Just keep practicing. Stropping more should smooth it out. Practice.
-
03-18-2006, 02:55 AM #5
- Join Date
- Jan 2006
- Location
- White Rock, B.C.
- Posts
- 53
Thanked: 0Originally Posted by JLStorm
Let you face heal. I still don't go against the grain after 10 weeks or so. But everyone's face is different . . . I would say to give it a couple of weeks at least. That way you can "hone" your technique.
Emil
-
03-18-2006, 03:19 AM #6
Lynn called me tonight, he said he thinks it might be the blade since I didnt have any of these problems with the other razor. I am going to ship it back to him so that he can take a look.
-
03-18-2006, 11:25 AM #7
Its important to have your own tools at home for blade tweeking issues like this. In the beginning most occur from the strop it self. Any overly aggressive angle shaving can even tear off the edge. I would suggest a fine barber hone or a paddle strop. It can also just be variances in the blade. I often prefer the softer steels, even if my stainless ones are honed perfectly. Sending the blade off to Lynn on occasion can be complemented with "homework". Or as the 12 year old in the house says "Your doing you honework".
-
03-18-2006, 03:40 PM #8Originally Posted by AFDavis11
-
03-18-2006, 04:40 PM #9Originally Posted by JLStorm
1. Normal shave of the upper lip.
2. Shave against the grain of the upper lip, but with the razor almost flat against the skin. In addition, I have to take slowing smaller swipes being careful not to "grab" the skin.
Good Luck,
Mark.
-
03-18-2006, 04:49 PM #10
JL, don't worry, it will all be fine after some 200-300 shaves. Serious.
Just don't worry about going across and against the grain, and the result will come. After some time (couple of months or so) you can start experimenting with tweaking your technique.
have fun,
Nenad