Thread: Thoughts on shave results with new razor

yea assuming the razor is up to snuff I would also guess the increased weight is the culprit.

Do i need to adjust my angle? It was a smooth shave except for all the redness that went away in 90 mins or so, but it was red. Now its fins smooth no nicks, cuts, or bumps.

Next time you shave with it analyze your technique. Are you using any more pressure to accomplish the results ? When I was starting out I found that excessive pressure led to irritation.

I LOVE my stosser wedge (and 6/8-1/4hol, and 15/16 hol). I also use an old warhorse - well worn B.J. Eyre wedge. With the wedges & the 1/4 hollow, it was easier for me to substitute pressure for a good stretch & proper angle. At that time, I wasn't able to use small (5/8) hollow because I didn't understand the wiki instructions on angle were a general rule of thumb for wtg. Since changing angle as needed, and changing to a very light contact pressure, I still get great shaves from the heavy grinds, but also get to enjoy the hollows. The heavy grinds simply allowed me to use pressure more easily than the flexible hollows.

You may be way beyond my experience there, but the others responding seem to be saying something similar about pressure/angle. I'll be flat amazed if you don't find that to be just a wonderful blade. If you don't like it, and I'm able to do anything about it - lets talk

On a side note, check to see if your normal angle/pressure gives any pull to the blade. The 1/4 hol. I got from John, and the stosser - both came w/ very good edges that didn't last long. After a couple weeks, the heels on both blades stopped lopping hanging hair & wouldn't revive with stropping. The monster hollow (15/16) was not really shave ready. With each blade, I was unable to reproduce John's stroke to use a finisher for touch-up. I had to reset bevels. Specifically on the stosser, I wish I'd have used 2-3 layers of tape. As delivered, John's edge completely mocked the received wisdom that wedges don't give feedback. Mine gave audible and tactile feedback really well. When I reset the bevel, I used no tape, and it made the bevel noticeably wider - and now the feedback is greatly reduced. It's conjecture on my part that the increased bevel width subdued the feedback, but the two changes appear to have happened at the same time.

Best of luck, Speckey. I think you made a very good choice w/ that wedge.

Speckey,

Shave with your new razor exclussivly for two weeks then you'll be in a better position to judge how it does and what technique works best.

I know I have been guilty of "trying too hard" when I use a new to me razor.

Relax. Shave. More will be revealed.

LG Roy

I have the exact same razor and I will say that it does take some getting used to. I have used it to shave four times so far and two of the shaves have been amazing, while the other two were exactly as you described. My face and neck were very irritated post shave.

I think the issue here is that this is a wedge and a very heavy blade. If you are used to shaving with something with a lighter grind and lighter weight, the same pressure cannot be used with the Wacker. I realize now that the two quality shaves I got from this razor I was super conscious of my pressure. I did not notice anything with an adjustment in the angle.

I say try shaving and be extra light with your pressure. Try to consciously float the razor over the skin and I think you will be surprised at the results. I shaved with the Wacker this morning and did not have the best shave, because I did not follow my own advice.

I known it might be hard to find out but it could be the way the razor was honed.

For me when I shave off of a coticule or other natural stones I get no irritation. But if I get a blade that has been sharpened with a norton or other synthetic hones they irritate me to no end.

I know skme other members here have mentioned the same so that could possibility.

But most likely it is just you gotten used to a new blade.

I think the problem was with the pressure. Today really no issues, again I to made sure I was light handed with the blade. I consider myself still a newbie as such have been using 5/8 hollow grounds. Going to this much larger wedge was a dramatic change. With that said you can only get better when you learn from your mistakes, know how to adjust angle and pressure. I am a work in progress
(in many ways). Thanks for all the help