Results 1 to 10 of 11
Thread: Repairing cut in strop....
-
04-24-2010, 03:03 PM #1
- Join Date
- Jan 2009
- Location
- Stay away stalker!
- Posts
- 4,578
- Blog Entries
- 1
Thanked: 1262Repairing cut in strop....
So a week ago I decide to replace the cut up latigo on my srd strop. Well, 2 days after purchasing my thumb slips on my return stroke and slice and dice!
sigh...
There is not a whole lot of "flap" to work with, so would contact cement still be my best bet? It does affect stropping, otherwise i would just leave it.
At this point I am tempted to just flip the leather around and see if i can avoid it with an x pattern....
Thanks
Attachment 41437
-
04-24-2010, 03:05 PM #2
If there is some flap, even a little bit, contact cement worked for me. In my case you wouldn't know it had been cut if you were to look and hadn't seen it before.
Edit; posted before you put the photo up. I think it would work and maybe rub fine pumice stone away from the flap (in the same direction as the flap, not against it ) after it is set up to get rid of any excess cement that could be seen on the strop.Last edited by JimmyHAD; 04-24-2010 at 03:07 PM.
Be careful how you treat people on your way up, you may meet them again on your way back down.
-
04-24-2010, 06:16 PM #3
Jimmy is right. you can do that or it is very small in the over hand you could just cut that small peace carefully. i don't think it will hurt much.
gl
-
04-24-2010, 06:33 PM #4
I've seen old strops used that had been cut into oblivion over the years and they work fine. Just as long as it's sanded down or the flaps don't hit the razor when you're stropping. The rest is merely aesthetic, imo.
-
04-25-2010, 01:18 AM #5
- Join Date
- Jan 2010
- Location
- LA, VA, MA and . . .
- Posts
- 51
Thanked: 14I did the same thing to one of my stops about a month ago. I second what JimmyHAD said; apply a very thin coat of contact cement, smooth it flat and then wipe off any excess. Wait until it dries, then lightly sand it (I think I used 800 grit sandpaper). It will smooth out, good as new!
-
04-26-2010, 05:31 PM #6
Rubber cement and then a light sanding with high grit paper to smooth off any excess glue or leather flaps. Should see you right as rain..!
I did this at least half a dozen times to my first strop, and I've caught my new one once or twice as well. Its very easy to do..!
-
04-29-2010, 01:04 PM #7
- Join Date
- Jan 2009
- Location
- Stay away stalker!
- Posts
- 4,578
- Blog Entries
- 1
Thanked: 1262DS(*DS(&#Q(
Well, the good news. I was able to repair that cut.
The bad news.. I put another cut in this strop today, using it for the first time in a week. Did it during my post shave 20 strokes...
This razor gives me fits sometimes stropping. It has a really large tang on it and get away from me sometimes when flipping.
Usually i catch myself before continuing the stropping motion though....
Pretty soon I will have tried the entire SRD line of leather and have a graveyard of abused strop leather.
-
04-29-2010, 11:02 PM #8
-
05-01-2010, 02:31 PM #9
That is a great shaver.
Now Good news is you know how to fix them . if i am not mistaken it should have some smile face to it.Just be careful next time.
-
05-02-2010, 02:00 PM #10
I have a huge Joseph Rodgers and sons To her majesties razor (7/8) wedge and it can be tricky to strop. It's a great razor though, it mows through hair.