Results 1 to 10 of 24
Thread: Duh! Centering blades.
Hybrid View
-
04-29-2015, 01:07 AM #1"Don't be stubborn. You are missing out."
I rest my case.
-
04-29-2015, 01:39 AM #2
You can also just sand the inside of the scale and then use a washer like you normally would. Or you can sand the tang right around the pivot. I do like you method, though.
-
04-29-2015, 01:43 AM #3
So simple.
Ed
-
The Following User Says Thank You to Chevhead For This Useful Post:
sharptonn (04-29-2015)
-
04-29-2015, 02:10 AM #4
I have certainly cobbed up some scales doing that. Don't have the touch! Some sort of woodworking mill with a pilot would be nice. Take an angle and dig in! Saw a fella do that here once. IF ca will stick to your scales, it seems great because you can sand a bit at a time and reassemble with microfasteners to test. Apart, a bit more.
I figure if it gets really thin in the process, another thin washer won't be noticible, and the thing would never spin
Sanding the scale inside is where I have a problem!
Some old razors may need a combination of the 2!"Don't be stubborn. You are missing out."
I rest my case.
-
04-29-2015, 03:32 AM #5
I use a dremel with one of those round burrs & grind the front of one side of the pivot hole & back of the other to tilt the blade on assembly.. Only do an area the size of the washer tho & not deep. As you said a few thou at the pivot makes for a lot of change at the wedge end.
Just to be clear, I grind at the scales not the razor tang.
Really skewed blades can hit the scales with the tail on fully opening. I have resorted to bending the tail a little in that case &/or even a bit of judicious grinding.“The white gleam of swords, not the black ink of books, clears doubts and uncertainties and bleak outlooks.”
-
The Following User Says Thank You to onimaru55 For This Useful Post:
sharptonn (04-29-2015)
-
04-29-2015, 02:04 AM #6
- Join Date
- Mar 2012
- Location
- Thunder Bay, Ontario, Canada
- Posts
- 17,251
Thanked: 3222
-
04-29-2015, 02:11 AM #7
simple is good tc
“ I,m getting the impression that everyone thinks I have TIME to fix their bikes”
-
The Following User Says Thank You to tcrideshd For This Useful Post:
sharptonn (04-29-2015)
-
04-29-2015, 03:19 AM #8
- Join Date
- Nov 2012
- Location
- Across the street from Mickey Mouse in Calif.
- Posts
- 5,320
Thanked: 1184As long as the glue holds your good to go. I usually just sand the scales until it works with test pins. If it gets off when pinning then the hammer trick (front of 1 pin back of the other) does it.
Good judgment comes from experience, and experience....well that comes from poor judgment.
-
The Following User Says Thank You to 10Pups For This Useful Post:
sharptonn (04-29-2015)
-
04-29-2015, 03:28 AM #9
Well aren't you the lucky dog! Seldom works for me. I reckon I get the wonkyest scales and blades of anyone!
I figure as long as the razor is pinned tightly, the CA will never let go until the bone crumbles under it.
If pinned tightly, BOTH sides would have to have let go in order for anything to move. Even then, the stiffness of the bone would not allow it. Hammer trick would not have fixed this! ...Puleeeeeeeze!Last edited by sharptonn; 04-29-2015 at 03:31 AM.
"Don't be stubborn. You are missing out."
I rest my case.
-
04-29-2015, 03:40 AM #10
Tool spoken of, Counterbore:
Available in different sizes and different guide tips. The drill bit was and illustration but any thing of the pilot diameter will work. Allen wrench is for fixing the pilot into pace.
~RichardBe yourself; everyone else is already taken.
- Oscar Wilde
-
The Following User Says Thank You to Geezer For This Useful Post:
sharptonn (04-29-2015)