Results 1 to 6 of 6
Like Tree12Likes
  • 4 Post By Pete123
  • 2 Post By outback
  • 1 Post By rolodave
  • 3 Post By Substance
  • 1 Post By ejmolitor37
  • 1 Post By Pete123

Thread: Working with Canvas Micarta

  1. #1
    Senior Member Pete123's Avatar
    Join Date
    Jan 2017
    Location
    Nashville, TN
    Posts
    350
    Thanked: 193

    Default Working with Canvas Micarta

    Someone saw the latest scales I did and asked about working with Micarta. I'll share my experience, which is limited. I'm sure some of the other folks that have used it will have comments as well.

    Micarta is the name of a product line made my Norplex-Micarta, thus Micarta isn't a generic name like Kleenex.

    I've worked with two of the products, both of which came from Masecraft. I have the tan canvas Micarta and the double red coral product.

    The product is very easy to work with, other than one area, which is achieving a polished finish. The issue is that the sanding dust gets stuck between the strands of canvas and doesn't look right. This was much less of an issue with the double red coral.

    The best way I came up with for dealing with this was to hand sand once the scales were shaped, utilizing a gun cleaning brush. This brush looks like a tooth brush, with much firmer bristles that a tooth brush.

    I would sand 2-3 strokes, then use the brush to remove the dust, repeating. I sanded up 220 grit before polishing. Then, I would polish, sand and brush, then repeat.

    As a side note, I'm going to sand to 220 grit on the next pair, do no further finishing, and see how the look after being handled for a while.

    A mentor suggested dome green polishing compound and I ordered a small assortment. I loaded the buffing wheel with green compound before reading the directions and turned the fabric in the tan scales green. It took a loooonnnnnggggg time to correct that mistake. It only takes a little compound.

    The green worked well on the double red coral. I'm sure it stained the the canvas as well, though it was dark and ended looking really good.

    I really like the way that canvas Micarta looks. I'm going to try some of their other products as well, made with linen or paper.

    One note for folks who are new at scale making. Masecraft sells a tremendous amount of G10 as well as Carbon Fiber with a G10 core.

    G10 uses fiberglass. When sanded, the dust is very similar to asbestos. It's just not worth the hassle to use the G10 safely in my opinion.
    Last edited by Pete123; 05-29-2017 at 08:55 PM.

  2. The Following 3 Users Say Thank You to Pete123 For This Useful Post:

    ejmolitor37 (05-29-2017), Gasman (05-29-2017), Geezer (05-29-2017)

  3. #2
    Senior Member blabbermouth outback's Avatar
    Join Date
    Mar 2015
    Location
    Akron, Ohio
    Posts
    11,925
    Thanked: 4300

    Default

    Couldn't you do a CA finish on them, it would give you that deep shine, and make the micarta really pop.!
    Gasman and Pete123 like this.
    Mike

  4. #3
    Moderator rolodave's Avatar
    Join Date
    Aug 2011
    Location
    Racine, WI USA
    Posts
    7,531
    Thanked: 1927
    Blog Entries
    1

    Default

    Hi Pete

    Could you position a vacuum intake right over the sanding area and let that take away the dust?
    I have never worked with micarta.
    Pete123 likes this.
    If you don't care where you are, you are not lost.

  5. The Following User Says Thank You to rolodave For This Useful Post:

    Pete123 (05-29-2017)

  6. #4
    Senior Member blabbermouth Substance's Avatar
    Join Date
    Jun 2013
    Location
    Gladstone QLD AUSTRALIA
    Posts
    3,245
    Thanked: 804

    Default

    yep the CA finish will help gloss them out if you want it to
    I think paper micarta is easier to polish up with normal sanding & polishing
    but the canvas & linen stuff is inherently textured, this is why it is great & highly recommended for knife scales
    G10 has a similar issue but finer grained

    and always use a good respirator and vacuum the dust from both G10 & any synthetic resins for that matter
    Last edited by Substance; 05-29-2017 at 09:43 PM.
    RezDog, outback and Pete123 like this.
    Saved,
    to shave another day.

  7. #5
    Senior Member blabbermouth ejmolitor37's Avatar
    Join Date
    Oct 2015
    Location
    Knoxville,IA
    Posts
    2,368
    Thanked: 762

    Default

    Thanks Pete been wanting to use this stuff and will in the future. So far I have only used bone and horn. Can't make em all the same so I'm gonna get some acrylic and micarta. Thanks for the write up much appreciated: )
    Pete123 likes this.
    Nothing is fool proof, to a sufficiently talented fool...

  8. #6
    Senior Member Pete123's Avatar
    Join Date
    Jan 2017
    Location
    Nashville, TN
    Posts
    350
    Thanked: 193

    Default

    Quote Originally Posted by rolodave View Post
    Hi Pete

    Could you position a vacuum intake right over the sanding area and let that take away the dust?
    I have never worked with micarta.
    Here's the smart money. I didn't think about that, of course you could and it would be so much easier.
    ejmolitor37 likes this.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •