View Poll Results: Desired distance between spacer and blade
- Voters
- 25. You may not vote on this poll
-
3 mm (short as possible)
18 72.00% -
5 mm (looking still good)
6 24.00% -
10 mm and more (please tell why)
1 4.00%
Results 11 to 20 of 26
84Likes
LinkBack URL
About LinkBacks-
12-09-2018, 12:14 AM #11At this point in time...
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 27,183
- Blog Entries
- 1
Thanked: 13250
Then vs Now
Keep in mind that many of the Vintage scales were not made of Impervious G10 and some of the near perfect materials we have now that have zip point nada change in 100 years
They had to build with a bit of "Slop" built in that we don't have to
they had limitations that we don't now 
"No amount of money spent on a Stone can ever replace the value of the time it takes learning to use it properly"
Very Respectfully - Glen
Proprietor - GemStar Custom Razors Honing/Restores/Regrinds Website
-
12-09-2018, 12:27 AM #12Senior Member
- Join Date
- Oct 2010
- Location
- 50 miles west of randydance
- Posts
- 9,699
Thanked: 1355
I wish that a couple of Red Imp's that I have would have had more spacing when manufactured.
-
12-09-2018, 12:43 AM #13Razor Vulture
- Join Date
- Oct 2010
- Location
- Lone Star State
- Posts
- 26,208
Thanked: 8626
Yeah....Those Case ones shrink so hard they can break the blade.
Blade closing tight to the wedge is desirable. A few MM's out can make a big difference on balance.
But then so can having more scale south of the bottom pin.
I have matched-up my fair-share and trust me. That is only ONE thing to consider when fitting scales.
Either making or swapping. A little is fine with me if that is how it has to be.
Here's your Red Imp, Tim! Don't try to open the blade, now!
OH! Those blade-busting Sta-Sharps needed an inch gap, I think!
Last edited by sharptonn; 12-09-2018 at 01:32 AM.
-
12-09-2018, 01:13 AM #14Skeptical Member
- Join Date
- Nov 2016
- Location
- Colorado Springs
- Posts
- 10,559
Thanked: 2197
Lol. That was a good one. I dont have one but i hear everyone complaining they shrink.
Originally Posted by 32t
I wish that a couple of Red Imp's that I have would have had more spacing when manufactured.It's just Sharpening, right?
Jerry...
-
12-09-2018, 01:28 AM #15Senior Member
- Join Date
- Oct 2010
- Location
- 50 miles west of randydance
- Posts
- 9,699
Thanked: 1355
Just round the nose and you will have a good shorty. Originally Posted by sharptonn
Yeah....Those Case ones shrink so hard they can break the blade
Blade closing tight to the wedge is desirable. A few MM's out can make a big difference on balance.
But then so can having more scale south of the bottom pin.
I have matched-up my fair-share and trust me. That is only ONE thing to consider when fitting scales.
Either making or swapping. A little is fine with me if that is how it has to be.
OH! Those blade-busting Sta-Sharps needed an inch gap, I think!
-
12-09-2018, 01:35 AM #16Senior Member
- Join Date
- Oct 2010
- Location
- 50 miles west of randydance
- Posts
- 9,699
Thanked: 1355
Keep adding pictures. Originally Posted by sharptonn
Here's your Red Imp, Tim! Don't try to open the blade, now!
Mine arnt that bad!
-
12-09-2018, 01:39 AM #17Senior Member
- Join Date
- Oct 2010
- Location
- 50 miles west of randydance
- Posts
- 9,699
Thanked: 1355
I have done the hacksaw blade on the wedge trick but I haven't looked at them recently........
-
12-09-2018, 01:40 AM #18Razor Vulture
- Join Date
- Oct 2010
- Location
- Lone Star State
- Posts
- 26,208
Thanked: 8626
Yeah. Looks like it will be a 'Zed Silver Steel' then! Originally Posted by 32t
-
12-09-2018, 01:41 AM #19Razor Vulture
- Join Date
- Oct 2010
- Location
- Lone Star State
- Posts
- 26,208
Thanked: 8626
Ah! The Holy Hacksaw Blade!. When you hit the pin, it's over! Originally Posted by 32t
-
12-09-2018, 01:45 AM #20Senior Member
- Join Date
- Oct 2010
- Location
- 50 miles west of randydance
- Posts
- 9,699
Thanked: 1355
One was really close.
No rust on the blade though........
Reply With Quote