Results 1 to 10 of 13
Thread: Is this worth saving?
-
09-17-2009, 03:18 PM #1
- Join Date
- Aug 2009
- Location
- Dallas, TX
- Posts
- 185
Thanked: 20Is this worth saving?
Before the rust and build up was removed, it seemed like a worth while endeavor but now that I can see the steel I'm starting to have second thoughts. These picture aren't great but I hope they show what I'm seeing. On one side, it seems that there was an attempt at a previous restore and the tang shows the damage, on the other side, the pitting seems to be pretty severe. Also, the blade is unevenly ground. So, what do you guys think? Go or no-go?
-
09-17-2009, 04:00 PM #2
Will it be a shaver: probably (and I'd bet a good one at that considering the Sheffield steel). Will it be a showroom piece: probably not. As long as their aren't cracks and the pitting isn't in the edge or messing up the blade geometry you should have a decent shaving blade. Think of the pitting as battle scars and the razor itself as a practice razor.
-
09-17-2009, 10:55 PM #3
Thats some pretty nasty swiss cheese at the tip, that may need removed to get to a shaveable edge. I have one that looks ok but is riddled with tiny holes all over the blade, hard to get past those.
-
09-17-2009, 11:00 PM #4
- Join Date
- Aug 2009
- Location
- Dallas, TX
- Posts
- 185
Thanked: 20I think this one is going to bare the horrors of my learning. Its going to get some spine work, bevel resetting, and geometry changes.
-
09-17-2009, 11:04 PM #5
-
09-17-2009, 11:09 PM #6
- Join Date
- Aug 2009
- Location
- Dallas, TX
- Posts
- 185
Thanked: 20How did that work out?
-
09-17-2009, 11:32 PM #7
- Join Date
- Jun 2009
- Location
- Sunny California!
- Posts
- 466
Thanked: 125Its pretty bad, but prolly worth saving. Definitly not worth getting all the pitting out tho, IMO.
-
09-17-2009, 11:37 PM #8
It was a 6/8+ Rodgers wedge, an impulse buy from the bay. What attracted me to it was the famous american eagle engraving - the same identical one ive also seen on W&Bs and John Barbers, & various other Sheffield makers.
Ironically what attracted me to that razor is long gone! After severe sanding there was swiss cheese everywhere, much worse than yours.
I put it in the razor bin for later work, until one day I saw a belt grinder in my friends garage which his dad uses for motorbike repairing - im not sure how.
He let me have a go, and while I managed to regrind the blade, it is pretty amateur and uneven. I wish I had consulted this forum first and got the right advice.
Ill try and post a picture if I remember when I get back 2 the UK. I may even try and fix it up a bit more.
But I enjoyed it which was the main thing, and it cost me about 15 dollars, so im not too out of pocketLast edited by Scipio; 09-17-2009 at 11:42 PM.
-
09-18-2009, 05:09 PM #9
- Join Date
- Aug 2009
- Location
- Dallas, TX
- Posts
- 185
Thanked: 20Thanks, I'd appreciate the pictures (if you happen to get around to it). I'm not too out of pocket on this, I can't remember what I paid, but it wasn't much. Thanks for your input.
-
09-18-2009, 07:37 PM #10
- Join Date
- Aug 2009
- Location
- Dallas, TX
- Posts
- 185
Thanked: 20Here is a shot of the razor halfway through its regrind.... its becoming a hollow so as to remove all the pitting. Any thoughts or advice?
Last edited by Carbonsteel928; 09-18-2009 at 10:06 PM.