Results 1 to 9 of 9
Thread: bent blade :(
LinkBack URL
About LinkBacks-
09-18-2009, 12:53 AM #1Senior Member
- Join Date
- Aug 2008
- Location
- Sydney, Australia
- Posts
- 113
Thanked: 19
bent blade :(
When time came to test fit the wedge, to my shock and dismay, I found that the spine is bent. If I put 3 washers on one side of the pin it fits without fouling the scales, but I want to avoid that because it looks pretty bad. The problem seems to be that the blade does not point directly down from the spine - its a couple degrees off.
Any tips on what to do?
-
09-18-2009, 01:24 AM #2Master of insanity
- Join Date
- Jul 2009
- Location
- London
- Posts
- 1,663
Thanked: 504
Could you plane the insides of the scales to overcome this?
-
09-18-2009, 01:38 AM #3Senior Member
- Join Date
- Nov 2005
- Posts
- 4,521
Thanked: 1636
check the threads we should have someone was showing how to fix with vise.GL
Last edited by hi_bud_gl; 09-18-2009 at 03:36 AM.
-
09-18-2009, 01:40 AM #4what Dad calls me
- Join Date
- Feb 2008
- Location
- Kansas city area USA
- Posts
- 9,173
Thanked: 1677
Like Sham said, stick it in a vise.
It is easier to fool people than to convince them they have been fooled. Twain
-
09-18-2009, 02:05 AM #5The Great & Powerful Oz
- Join Date
- May 2008
- Location
- Bodalla, NSW
- Posts
- 15,627
Thanked: 3749
The white gleam of swords, not the black ink of books, clears doubts and uncertainties and bleak outlooks.
-
09-18-2009, 03:38 AM #6< Banned User >
- Join Date
- Feb 2008
- Posts
- 3,763
Thanked: 735
On a big ol' blade such as that what I have often found is not so much that the spine is bent (ala the Double Arrow), but that they put an angle on only one side of the tang, instead of both symetrically.
The vice trick works fine for a DA, but I would not use that as option #1 on a 1/4" thick tang such as probably exists on that big'un.
As mentioned above, you can sand an angle into the inside of one of your scales to get it to sit evenly. Much less intrusive than extra spacers, as you have said are a bit ungainly.
-
09-18-2009, 04:27 PM #7< Banned Scammer >
- Join Date
- Jun 2009
- Location
- Sunny California!
- Posts
- 466
Thanked: 125
Sorry to hear this dunn
I hope that you can fix the tang, as I know how much you like that blade... Unfortuneately, I dont have much advice to offer...
-
09-21-2009, 05:32 AM #8Senior Member
- Join Date
- Aug 2008
- Location
- Sydney, Australia
- Posts
- 113
Thanked: 19
thanks chaps - its a thick tang, so im going to mess with the scales, rather than with the actual blade. The angle of the tang is causing the problem I think, its not completely flat on one side, but its close.
Ill probably put an extra pin on either side and plane out the scales a little.
-
09-21-2009, 01:42 PM #9Senior Member
- Join Date
- Dec 2006
- Location
- Burkburnett TX
- Posts
- 3,100
Thanked: 2392
If you have some micorasteners or other little nuts and bolts it makes
adjusting the centerig a lot easier. Put the razor together with the
temporary fasteners and use an emory board or small file to remove the
wood. In my experiance it takes less sanding than I think it will to
make a change in the centering of the blade. According to my quick and
dirty calculations a .005" (thickness of nice copy paper) change by the
tang will make a .015" or 1/64" at the end of the blade.
Charlie
Reply With Quote