Results 1 to 10 of 17

Hybrid View

JerseyMike Newbie w/Rust Spots.. help! 11-07-2010, 09:56 PM
Blackstangal Is this a new razor? I use... 11-07-2010, 10:06 PM
rostfrei Carbon razors are prone to do... 11-07-2010, 10:12 PM
baldy Your right, in my opinion... 11-07-2010, 10:49 PM
JerseyMike Thanks for the quick... 11-08-2010, 01:37 AM
juannaredo toilet paper 11-08-2010, 05:13 AM
Maxi I'm on the toilet paper... 11-08-2010, 11:34 AM
Undream I am nearly positive that... 11-08-2010, 12:38 PM
life2short1971 I found that running the... 11-08-2010, 02:51 PM
cpcohen1945 There is a new "anti-rust"... 11-09-2010, 03:10 AM
JerseyMike Anti-rust barbicide could be... 11-09-2010, 03:20 PM
JerseyMike Here are 2 pictures of the... 11-09-2010, 04:11 PM
ZethLent As it doesn't look like... 11-10-2010, 02:07 AM
pinklather Utopian has the hot tip on... 11-10-2010, 04:36 AM
Lynn Almost every time we see this... 11-10-2010, 04:56 PM
life2short1971 You may find it easiest to... 11-10-2010, 05:01 PM
JerseyMike Thanks for all the tips guys,... 11-15-2010, 05:25 AM
  1. #1
    Brad Maggard Undream's Avatar
    Join Date
    Jan 2009
    Location
    Adrian, Michigan
    Posts
    879
    Thanked: 693

    Default

    I am nearly positive that barbicide CAUSED rust on a w&b I had in my possession..

    I don't use it anymore!!

  2. #2
    Senior Member
    Join Date
    Sep 2010
    Location
    North Central florida
    Posts
    213
    Thanked: 30

    Default

    I found that running the blade under hot water to heat it before wiping dry works well.

  3. #3
    Senior Member
    Join Date
    Aug 2010
    Location
    Vancouver, BC, Canada
    Posts
    1,377
    Thanked: 275

    Default

    Does anybody think barbicide is a good way to prevent rust?
    There is a new "anti-rust" Barbicide formulation. I'd trust that, not the original Barbicide.

    I'm putting a thin coat of oil on the blade. In my experience, high-carbon steel rusts if you look at it sideways.

    Charles

  4. #4
    Junior Member
    Join Date
    Nov 2010
    Posts
    5
    Thanked: 0

    Default

    Anti-rust barbicide could be something worth exploring. I looked around the forum and found a guy with my exact same problem AND the same model of Dovo. The picture he posted nearly matched my issues here, a few "spots" of light brown, it was mostly attributed to hard water stains in his case (I wish I remembered the forum link!). He said he used CLR on it and it cleared it up.

    Since I've been drying it thoroughly and storing it in the bedroom rather than the bathroom, there's been no new rust or stains.

  5. #5
    Junior Member
    Join Date
    Nov 2010
    Posts
    5
    Thanked: 0

    Default

    Here are 2 pictures of the razor (best I could do) ... you can see the "spots"

    http://straightrazorpalace.com/membe...t-img00035.jpg

    http://straightrazorpalace.com/membe...t-img00033.jpg

  6. #6
    Member ZethLent's Avatar
    Join Date
    Aug 2007
    Location
    Japan
    Posts
    658
    Thanked: 335

    Default

    As it doesn't look like active rust, I think either a little bit of metal polish or a polishing cloth with embeded polish will take those away in due course. As someone who is new to this you will just have to gain confidence in handling the razor so that you can confidently wipe it down with a facial tissue or peice of toilet paper (even close to the edge). Also you need to make sure that there is no water on the inside of the scales. Poke the corner of a facial tissue in between, when the razor is open, and pull it through to catch any small drops of water. Blowing only may still leave water.

    FYI, I live in Japan and it is very humid here, as it is in places in the USA too, but I have never had any rust or water spots (like what I see on your razor) after drying the razor this way. I also never use oil.

    Good luck.
    笑う門に福来たる。

  7. #7
    Senior Member blabbermouth
    Join Date
    Jul 2010
    Location
    Portland, OR
    Posts
    2,697
    Thanked: 830
    Blog Entries
    1

    Default Utopian has the hot tip on blade care/coating

    Dissolve 1 tablespoon mineral oil in 1 qt denatured alchohol. After post shave strop, dip the blade & set out to air dry. Alch. evaporates, leaves a coating of oil so thin there's no need to wipe - just strop & shave. The blade may have a cloudy appearance, if high luster shine is present, but that's just the oil doing it's job.

  8. #8
      Lynn's Avatar
    Join Date
    May 2005
    Location
    St. Louis, Missouri, United States
    Posts
    8,454
    Thanked: 4942
    Blog Entries
    2

    Default

    Almost every time we see this problem, the cause is a new guy rinsing the scales or getting them wet in the process of shaving or rinsing the blade. This is the Big No-No. You should just rinse the blade when shaving and be careful not to get water anywhere else. Then dry the blade and leave it open to fully dry before you put it up or coat it with oil.

    Most times the staining will come off easily, but if the staining is where there is etching or gold wash, they will also come off.

    Have fun,

    Lynn

  9. #9
    Senior Member
    Join Date
    Sep 2010
    Location
    North Central florida
    Posts
    213
    Thanked: 30

    Default

    You may find it easiest to control the water splashing by using a rag or damp sponge to wipe the blade with after each pass on your face. I have a round sponge that is 6x2 and it works very well.When I am done I run the blade only under hot water to warm it and wipe it dry. It seems to dry better that way.

  10. #10
    Junior Member
    Join Date
    Nov 2010
    Posts
    5
    Thanked: 0

    Default

    Thanks for all the tips guys, I'm following the advice and it's MUCH better now, no new spots, no rust, etc.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •