Results 1 to 10 of 15
Thread: Flush Cutter Recommendations
Hybrid View
-
10-25-2012, 04:38 AM #1
- Join Date
- Dec 2011
- Location
- Lakewood, WA
- Posts
- 533
Thanked: 56Michael's has flush cutters in ... but your man-card gets left at the checkout I am afraid. They have glittery handles lol.
Oh Glen, why couldn't I have seen this advice before they stole my man-card
-
10-25-2012, 04:46 AM #2
I've also gotten some halfway decent Kobalt branded flush cutters in a big blister pack with other tools at Home Depot. The handles, of course, didn't stay on, so I drilled holes through the metal and made new (and more ergonomic!) handles using some polycaprolactone.
Another useful mod with flush cutters: sand the flat side to a mirror finish. Just like a peening hammer, the more polished the surface, the less it'll mark up whatever you're working on.
I also use the Harbor Freight flush cutters. Like Glen says, they're cheap. You can also buy from them online.-Zak Jarvis. Writer. Artist. Bon vivant.
-
10-25-2012, 07:16 AM #3
Prahston,
An observation on using flush cutters - I was de-pinning a French razor using a high quality brand of flush cutters - there was a snapping sound and the tip of one blade of the flush cutters left a dent in my safety glasses - turns out the pin was made of steel !!
Please always wear safety glasses when de-pinning and cover work with a cloth to protect yourself
Have fun !
Best regards
RussLast edited by PhatMan; 10-25-2012 at 07:21 AM.
-
The Following User Says Thank You to PhatMan For This Useful Post:
Hirlau (10-25-2012)
-
10-29-2012, 05:41 PM #4
Great information all around! Especially about the Safety Glasses... I actually have two pair within easy reach for just that reason but still wear them only half the time... Gotta get better about that!!!!!!!
I did more work this past weekend on Razors and cut my disassebmly time from about 30 minutes to a minute and half using the flush cutters!
Thanks for all the information! If I had all day every day I'd never be able to absorb all that is here so I'm just trying to soak up and use what I can as I go!
Just an absolute total blast!
Here's a pic of some of my latest work:
Top Left: Boker 'Red Injun' that I unpinned, cleaned up/shined, re-pinned, honed and is now good to go.
Top Right: Century Cutlery 'Radio Steel' that I had previously put new scales on and just got a touch up on the Naniwa and re-stropped with paste to bring it to a bit better level.
Bottom Left: Wostenholm 1XL that was an eBay grab that just needed cleaned up/shined and honed.
Bottom Right: My first 'usable' WB from some time back that was my first successful hone to 'Shaving Sharp', just got a touch up run through a better pyramid I'm trying out then run through my better srops.
Bottom Center: WB 'Special' that was a more recent eBay grab just taken apart and ready for a week of hand-polishing/shining and honing coming up. Used my new purchase of a set of Flush Cutters and dropped my tear down time from about 30 miinutes to a minute and a half!
-
10-31-2012, 03:26 AM #5
You can get good deals on eBay for used high quality cutters. The smaller the tip of the flush cutter, the better to grab pins from old razors. I use steel pins on my razors now. If you do not use cutters with high quality steel, the edge will snap and chip.get good ones even if they are used.
-
10-31-2012, 08:47 AM #6
I've never done any razor restoration... but you can get about any kind of cutters (Flush cut etc.) from Snap-on Tools... If you don't have a local dealer you can order them online at Snap-on: Hand Tools, Power Tools, Tool Boxes, Automotive Diagnostics and Shop Equipment