Results 1 to 10 of 15
Hybrid View
-
01-05-2013, 06:10 PM #1
- Join Date
- Feb 2010
- Location
- Upper Middle Slobovia NY
- Posts
- 2,736
Thanked: 480If your going for hand work, toothbrush is good idea. BUT, make sure that it is a firm or hard brush, and not one of the "soft" variety. Then, instead of metal polish, use some of the rubbing compounds on it.
-
01-05-2013, 06:15 PM #2
- Join Date
- Jan 2011
- Location
- Roseville,Kali
- Posts
- 10,432
Thanked: 2027Just make sure that whatever compounds you use are softer than the razor.To my eye is nothing worse than to see rounded off hand cut jimps on restos.
-
01-05-2013, 07:34 PM #3
- Join Date
- Nov 2012
- Location
- Across the street from Mickey Mouse in Calif.
- Posts
- 5,320
Thanked: 1184I have a rotatory tool and was going to offer to experiment for you. HA I have no jibs. Oh well. I do have a pack of these that I started to use for cleaning and polishing my razor as they get into some places with a firm pressure. Like between scales and same only on the tang where it goes thru the scales. They have some thickness to them but I don't know if they would reach the bottom of a jib. I supposed you could use a polishing paste on them to some extent too. I have yet to experiment with that.
Good judgment comes from experience, and experience....well that comes from poor judgment.
-
01-05-2013, 07:58 PM #4
-
01-05-2013, 08:08 PM #5
- Join Date
- Nov 2012
- Location
- Across the street from Mickey Mouse in Calif.
- Posts
- 5,320
Thanked: 1184They are a pretty stiff plastic and the non covered end makes a fairly good scraper. Maybe could sharpen it some. I have just used it with blue magic but this thread got me to thinking about other things that I have to try now. I have used just that one stick for about 8 razors so far and no signs of it falling apart yet.
Good judgment comes from experience, and experience....well that comes from poor judgment.
-
01-05-2013, 10:34 PM #6
I use 000 synthetic steel wool with MAAS. Honestly, I don't think jimps are supposed to be shiny...
-
01-06-2013, 06:02 PM #7
The shiny parts of a razor got shiny at the factory because someone put it on a polishing wheel. The polishing wheel DID NOT get down into the jimps.
When you're talking about old Sheffield blades, typically only the blade face was done to a mirror polish. The spine and tang were left with the finish from the final shaping grind, done on emery wheels.-Zak Jarvis. Writer. Artist. Bon vivant.
-
The Following User Says Thank You to Voidmonster For This Useful Post:
JoeLowett (01-06-2013)
-
01-08-2013, 09:21 PM #8
I have used a quality ( Jewelers' grade) finely cut needle file. I find the cross section which is closest to the original jimp cut. Usually that would be a tri corner, flat oval, or a knife shape. I then set the blade into a narrow slot cut the long way into a 6" long 2x2 which is longer that the blade portion of the razor and supports the shank and spine without allowing the edge and bevel to make contact anywhere. I then carefully align the file perfectly along the existing jimp slots and one slow careful stroke will normally get to the bottom. The jig is also great for sanding the spine and tail because it can secure the razor and held in one hand while working on them with the other hand.
The shanks and tails of a razor are usually not well hardened so a file will cut quickly. Be careful or all is for naught!
Richard
-
01-05-2013, 07:54 PM #9