Results 1 to 10 of 16
Like Tree3Likes

Thread: Using loupe I see a jagged edge towards tip of razor.

Hybrid View

  1. #1
    Junior Member
    Join Date
    Feb 2015
    Location
    Munster, IN
    Posts
    16
    Thanked: 1

    Default

    Hi I have been straight razor shaving for over 3 months and have 3 razors. This is a Dovo Bismark and I find it not as smooth as the Ralf Aust I have and even that of my vintage Heckles that I actually honed myself and after using the loupe I seen a much better bevel on both of these razors (finer scratch pattern ). I was wondering if I could use the 3k and do circles followed by the x strokes then progress to the 8k then 12 k? I use a DMT 325 for lapping.


    Jim

  2. #2
    Truth is weirder than any fiction.. Grazor's Avatar
    Join Date
    Jun 2012
    Location
    Land of the long white cloud
    Posts
    2,946
    Thanked: 581

    Default

    You could try a touch up on the Dovo with the 12k, 10-30 laps and test shave. Might be all it needs.
    Into this house we're born, into this world we're thrown ~ Jim Morrison

  3. #3
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,457
    Thanked: 4830

    Default

    It is a tough one to do sight unseen. It depends on hoe small these little serrations are. Are we talking the full depth of the bevel just a little fuzz on the very edge. If you are really wanting to do this and the is no holding back. The first go should be with 3K presuming it is very tiny on the edge. I would try ten x strokes and then check it. Pressure is your enemy at this point in the game. A reasonable indicator is watching your water and how it clears the hone. Try a couple of stroke light enough that you are moving the water with the edge, but not all of it, sort of splitting it in half, then add a little more pressure until you are barely able to clear the water. That is the amount of pressure needed. It is very light handed. One of the risks is that you will do too much work on your edge and it will start to fall apart. Tread lightly and go slow.
    armourpc likes this.
    It's not what you know, it's who you take fishing!

  4. #4
    Junior Member
    Join Date
    Feb 2015
    Location
    Munster, IN
    Posts
    16
    Thanked: 1

    Default

    Fuzz at very edge.

  5. #5
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,457
    Thanked: 4830

    Default

    The pretense of my previous post is that I am under the assumption that you have damaged your edge while stropping. Seeing as how we are talking about the very edge you are likely better off starting with Grazors advice. Starting high will preserve more metal. If you do two sets of ten laps and you cannot see the fuzz disappearing then drop to the next highest grit hone and then once they are gone start back up.
    It's not what you know, it's who you take fishing!

  6. #6
    Junior Member
    Join Date
    Feb 2015
    Location
    Munster, IN
    Posts
    16
    Thanked: 1

    Default

    Got it Rezdog :-). I am happy with results too!!!! I used a 3k Naniwa and did 20 circles with pressure followed by 20 with pressure x-strokes then went to 8 k did 40 circles ( weight of blade only ) followed by ten x-strokes ( weight only ) then did 10 x-strokes on 12k Naniwa and now bevel is smooth and no more jagged edge ( yay ). Thanks all you fine gents on here you are all the best.
    Last edited by Brag251; 03-16-2015 at 07:46 PM.

  7. #7
    Senior Member blabbermouth
    Join Date
    Apr 2012
    Location
    Diamond Bar, CA
    Posts
    6,553
    Thanked: 3215

    Default

    If you had micro-chip, fuzz, a 12k super stone can easily take them out.

    Put one layer of tape on the spine and do 1 set of 20 circles on each side and 20 X laps with weight of the blade pressure.

    Look at the edge straight down to see if there are any shiny spots, If not strop on linen 20 laps with very lite pressure and 50 on leather with lite pressure. Excessive pressure probably caused your mico-chipping.

    If there are shiny spots, do another set of 20 circles and X laps.

    The 12K super stone is a very aggressive stone, take a look at this thread taking a razor from breadknife to shave in 80 circles and 206 laps.

    Here.

  8. The Following User Says Thank You to Euclid440 For This Useful Post:

    pcm (03-17-2015)

  9. #8
    Junior Member
    Join Date
    Feb 2015
    Location
    Munster, IN
    Posts
    16
    Thanked: 1

    Default

    Thanks Euclid I appreciate it and great post also :-)

  10. The Following User Says Thank You to Brag251 For This Useful Post:

    Euclid440 (03-17-2015)

  11. #9
    Member Lutebro's Avatar
    Join Date
    May 2014
    Location
    Olympia, WA
    Posts
    62
    Thanked: 6

    Default

    This was a great question and for someone else in the process of learning honing quite valuable!

  12. #10
    www.edge-dynamics.com JOB15's Avatar
    Join Date
    Feb 2013
    Location
    London
    Posts
    3,066
    Thanked: 512

    Default

    Quote Originally Posted by Euclid440 View Post
    If you had micro-chip, fuzz, a 12k super stone can easily take them out.

    Put one layer of tape on the spine and do 1 set of 20 circles on each side and 20 X laps with weight of the blade pressure.

    Look at the edge straight down to see if there are any shiny spots, If not strop on linen 20 laps with very lite pressure and 50 on leather with lite pressure. Excessive pressure probably caused your mico-chipping.

    If there are shiny spots, do another set of 20 circles and X laps.

    The 12K super stone is a very aggressive stone, take a look at this thread taking a razor from breadknife to shave in 80 circles and 206 laps.

    Here.
    What are the shiny spots, if I may ask? (not the burrs ,chips and such but just a shiny spot)
    I some times have a few near the toe end, I assumed they were where the metal is thin and could possibly micro chip later.
    Last edited by JOB15; 03-17-2015 at 07:35 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •