Page 2 of 4 FirstFirst 1234 LastLast
Results 11 to 20 of 37
Like Tree62Likes

Thread: Complete the progression, a FUN exercise!:)

  1. #11
    Senior Member blabbermouth
    Join Date
    Apr 2012
    Location
    Diamond Bar, CA
    Posts
    6,553
    Thanked: 3215

    Default

    I have tried most of the combinations and others, not listed. It really does not matter, if you are finishing on a 12k Super Stone and or a SG20. I usually mix the 1-12k stones, with a variety of stone, almost daily and there is no difference on the finished edge.

    If you are going to jump to a natural finisher the 8K, Naniwa old Snow White Junpaku, is a nice pre-finish stone, but not, that much nicer than a Norton 8k that it would make, that much of a difference. But if you finish on a 12k, higher or natural, then it makes no difference.

    Mix and match makers, as long as, they are quality stones. The low grit stones don’t matter, especially if you are not pro-honing.

    What matters is setting a bevel fully, on an 800 - 4k, and finishing the edge as straight as possible. Technique and experience.

    Hone a thousand razors, with the progression you have, then decide.

  2. The Following User Says Thank You to Euclid440 For This Useful Post:

    gabrielcr78 (03-15-2017)

  3. #12
    Senior Member Wayne1963's Avatar
    Join Date
    Feb 2013
    Location
    South Carolina, USA
    Posts
    1,181
    Thanked: 162

    Default

    My favorite progression is: secure blade in scales with rubber bands, cover with bubble wrap, place in box then send it to someone that knows what the heck they are doing.

    I've actually had successes in honing, but I'd rather let someone else do the heavy lifting, then just maintain with stropping and a 12k SS. For some strange reason, I like the tension of sending your baby out, then the anticipation of her return.
    Marshal likes this.

  4. The Following User Says Thank You to Wayne1963 For This Useful Post:

    tcrideshd (03-16-2017)

  5. #13
    Senior Member
    Join Date
    Nov 2012
    Location
    Seattle,WA.
    Posts
    579
    Thanked: 55

    Default

    I don't think the progression is crucial. The end result is likely to be the same whatever you do.

  6. #14
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,552
    Thanked: 3795
    Blog Entries
    1

    Default

    I can get by just fine with nothing but a barber hone, but that was not what the OP asked.

  7. #15
    Senior Member blabbermouth
    Join Date
    Dec 2014
    Location
    Virginia, USA
    Posts
    2,224
    Thanked: 481

    Default

    Quote Originally Posted by Utopian View Post
    I can get by just fine with nothing but a barber hone, but that was not what the OP asked.
    This. I can get by with a 1K bevel setter and a Barber hone. But, you can't stop HAD. Sure he can get along perfectly fine with his Norton hones. But even if he chose to stick with them, there'd still be that Naniwa itch just waiting to be scratched. If not now, then later on down the line. All you can really do is tell someone which hone(s) you'd pickup and why. What they do with that information is up to them.
    gabrielcr78 likes this.

  8. #16
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,552
    Thanked: 3795
    Blog Entries
    1

    Default

    Quote Originally Posted by Marshal View Post
    I can get by with a 1K bevel setter and a Barber hone.
    Nah...

    You don't need the 1k.



    Back when all I had was a couple of barber hones, I assumed that I could not use much pressure and so a typical bevel set took a couple of hours. Now, I can do a bevel set on an average undamaged full hollow in about 10-15 minutes on a Swaty.

    That is, I CAN and I HAVE, but I ain't gonna do it again unless it's to prove it to someone else!
    JackeHj, Marshal, MW76 and 1 others like this.

  9. #17
    Senior Member blabbermouth
    Join Date
    Dec 2014
    Location
    Virginia, USA
    Posts
    2,224
    Thanked: 481

    Default

    The 1k is more of a want. I've gotten spoiled. I have learned you can do a lot with a Swaty. More than I would've suspected, and faster at that. But as you said, not something I'd want to do regularly.
    gabrielcr78 likes this.

  10. #18
    Senior Member gabrielcr78's Avatar
    Join Date
    Oct 2016
    Posts
    983
    Thanked: 134

    Default

    Quote Originally Posted by Utopian View Post
    I can get by just fine with nothing but a barber hone
    oh boy...



    Quote Originally Posted by Utopian View Post
    That is, I CAN and I HAVE, but I ain't gonna do it again unless it's to prove it to someone else!
    hummmmm .. should I..... .... .... .... naaaah!, I believe you!
    Last edited by gabrielcr78; 03-15-2017 at 05:24 PM.
    Marshal likes this.
    honing my mind...

  11. #19
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,552
    Thanked: 3795
    Blog Entries
    1

    Default

    Eventually I'll get a second camera and then I can do a proper set of honing videos. When that happens, I'll do full Swaty honing. Don't hold your breath though.

  12. #20
    Razor Vulture sharptonn's Avatar
    Join Date
    Oct 2010
    Location
    Lone Star State
    Posts
    26,100
    Thanked: 8612

    Default

    Quote Originally Posted by Marshal View Post
    The 1k is more of a want. I've gotten spoiled. I have learned you can do a lot with a Swaty. More than I would've suspected, and faster at that. But as you said, not something I'd want to do regularly.
    Is that not a bit contradictory?

Page 2 of 4 FirstFirst 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •