Page 1 of 2 12 LastLast
Results 1 to 10 of 14
Like Tree34Likes

Thread: The surprising ease of Coticule (Dilucot)

  1. #1
    MHV
    MHV is offline
    Member MHV's Avatar
    Join Date
    Jun 2010
    Location
    Montréal, QC
    Posts
    88
    Thanked: 41

    Default The surprising ease of Coticule (Dilucot)

    After five years with a single straight razor (DOVO best 6/8 half hollow), I have developed a good feel for the basic techniques: lathering, stropping, finding the beard's grain, adjusting pressure and angle, and speed. Although I succeeded in maintaining an edge, I never managed an edge that fully satisfied me. My tools were a barber's hone, and a pasted strop (1 micron / CrOx). A couple laps on the wet, then dry hone, then the pasted strop, then normal stropping, and I would get a workable edge. However, since I started shaving the whole face (bye-bye goatee!), I have been having problems with the chin.

    Switching gear sure has helped understand my previous limitations. On my 35th birthday, I splurged on a new Böker Arbolito and a natural combo Coticule. I had been thinking about a full hollow for a while, and man, should I have gotten it earlier. But the real surprise was the Coticule. I wanted to do the whole edge myself on it, and not rely on a honing service. So I read high and low, and I ended up trying the Dilucot procedure.

    Now, some seem to make a big fuss of honing, and I'm sure you could spend an inordinate amount of time getting that perfect edge, especially on natural hones, but DON'T LET THAT IMPRESS YOU! The point of honing is to get an edge, not a medal. If it shaves, and you like it, and you skin likes it to, then YOU WON!

    I blunted the factory edge on glass, and made sure it didn't shave arm hair. Then I raised a slurry on the Coticule side until it resembled milk (3.25% fat). I did two sets of 30 half-strokes with light pressure. I aimed for the nicest slurrrrrrpsh sound to adjust pressure. Then I did about 10 sets of 15 half-strokes diluting the slurry. I added a finger load of water at each set. By the end, one drop at a time, I ended up with an almost clear stone. I rinsed everything, and did two sets of 30 X-strokes on water. Wipe dry, then 60 laps on linen, 60 on leather, shave!

    The only improvement I made so far was to do the intermediate step on the Belgian Blue side of the hone. I worked the Coticule side with slurry as above, then I switched side, and raised a lighter slurry (more like skim milk!). I did my 10 sets of half-strokes, adding one drop of water at a time. Then I finished back on the Coticule with water. I gained noticeable sharpness, but both edges are equally smooth, and my chin is perfect each time. I can now shave every day with my straight, with zero irritation (something that even a quality DE blade couldn't do since it would shave very close yet rip some skin off too).

    I can't get enough the smoothness, and of the fact that I did it all by myself with a single hone. Granted, I'm not sure I could repair a POS razor from flea market, but I don't care either!

    The lesson in all this is that I hit the rock with my DOVO, and it ended up almost as nice as the Böker. As the DOVO is a half-hollow, I think it will need more honing to get the proper edge, though.

    Name:  IMG_0156.jpg
Views: 518
Size:  45.8 KB

  2. The Following 2 Users Say Thank You to MHV For This Useful Post:

    Geezer (06-06-2015), sharptonn (06-06-2015)

  3. #2
    Customized Birnando's Avatar
    Join Date
    Feb 2010
    Location
    Oslo, Norway
    Posts
    5,079
    Thanked: 1694

    Default

    I love reading stuff like this.
    Well done mate, well done!
    You a hone nut now
    rolodave and Steel like this.
    Bjoernar
    Um, all of them, any of them that have been in front of me over all these years....


  4. #3
    Senior Member blabbermouth tcrideshd's Avatar
    Join Date
    Oct 2013
    Location
    Oakland Tn
    Posts
    6,586
    Thanked: 1894

    Default

    Congratulations!!! And welcome back Bjoernar. Haven't seen you in a while. Tc
    Geezer likes this.
    “ I,m getting the impression that everyone thinks I have TIME to fix their bikes”

  5. The Following User Says Thank You to tcrideshd For This Useful Post:

    Birnando (06-05-2015)

  6. #4
    Senior Member blabbermouth edhewitt's Avatar
    Join Date
    May 2013
    Location
    Perth Australia
    Posts
    7,741
    Thanked: 713
    Blog Entries
    1

    Default

    nice story, and good to see other minimalists around too, in fact you beat me hands down
    Bread and water can so easily become tea and toast

  7. #5
    Senior Member DireStraights's Avatar
    Join Date
    Jul 2014
    Location
    Sonoma, California
    Posts
    165
    Thanked: 22

    Default

    Good job. My only comment is on your linen laps. 60 seems like overkill IMO. I usually do half what I do on leather. If it works for you that is awesome though. If I were you I would experiment with less linen and see if you get different results.

  8. #6
    Senior Member
    Join Date
    Oct 2014
    Location
    Denver, CO
    Posts
    207
    Thanked: 11

    Default

    I am curious, do you know what variety (vein type), if any, the coticule is? These stones seem to get a hard time here sometimes..Good post! Thanks

  9. #7
    Senior Member Badgister's Avatar
    Join Date
    Aug 2008
    Location
    Montreal, Quebec
    Posts
    1,630
    Thanked: 260

    Default

    Great to read a success story like this, especially from a fellow Montrealer. I discovered the joys of one stone coticule honing late in this hobby. It truly is a great stone for straight razors. Congrats!

  10. #8
    illegitimum non carborundum Utopian's Avatar
    Join Date
    Jan 2008
    Location
    Rochester, MN
    Posts
    11,544
    Thanked: 3795
    Blog Entries
    1

    Default

    The reality is that we can make this as complicated or as simple as we like. Congrats on your simple success!
    Geezer and tcrideshd like this.

  11. The Following User Says Thank You to Utopian For This Useful Post:

    Geezer (06-06-2015)

  12. #9
    Senior Member Willisf's Avatar
    Join Date
    Sep 2014
    Location
    Yorkton, Saskatchewan, Canada
    Posts
    1,171
    Thanked: 230

    Default

    Your post is very refreshing to read. I love to hear success stories.
    Glad it all worked out for you!

    Slow and easy wins the race.

    Is it over there or over yonder?

  13. #10
    MHV
    MHV is offline
    Member MHV's Avatar
    Join Date
    Jun 2010
    Location
    Montréal, QC
    Posts
    88
    Thanked: 41

    Default

    Thanks all; I picked 60 linen as an arbitrary recommendation from Coticule.be. I don't know the layer of my hone, got it from Fendrihan.

    I think the intertubes tend to foster the proliferation of information, but also the spreading of received ideas. I'm hoping that this post encourages others' self-confidence in DOING rather than merely bouncing information.

  14. The Following User Says Thank You to MHV For This Useful Post:

    Pringr (06-06-2015)

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •