Thread: Bevel issue? Or what?

So I am still pretty new to this so I could really use some help right now. When I got my SR I got a norton 4/8k so that I could hone it myself instead of paying someone every couple of months. It took me about 4 or 5 tries but I finally got the edge pretty nice to the point where it was a comfortable and pretty close shave. I Know there is still some technique issues but I think I might have a bad bevel.

The past week or, Like I said, I finally had some pretty good shaves and the razor felt nice and sharp. However today one side of my neck is significantly closer than the other. (I have a full beard on the face so I really only shave my neck and clean up the cheeks a bit.) Is it possible that this is a bevel issue? That one side of the razor is sharper than the other?

Although I know my technique isn't the best right now, I doubt that this is a technique issue. I say this because the side that is closer is the side that I am less confident with. I have more nicks, and close calls on this side than the other. I am often correcting my angle on this side so that the razor glides smoothly.

If this is a bevel issue is there any suggestions to helping with this? When I set my bevel I do a set of circles with each hand to try to avoid a biased edge (better on heel or toe). Could this be worse for me? Any suggestions would be greatly appreciated.

With REALLY REALLY bad techniques and effort I guess it would be possible to actually offset an edge and create a edge that is at a different angle on one side -vs- the other, but not actually a sharper edge ..

Geometrically the razor is designed to make a centered bevel, so if the bevel was offset it would either have to be a bad mis-grind or a serious screw up honing..

I am assuming you have watched the Vids, the only thing you posted that gives me pause is this statement

Originally Posted by freddi

When I set my bevel I do a set of circles with each hand to try to avoid a biased edge (better on heel or toe). Could this be worse for me?

Not really sure of what you are doing there or why

When using circles you want to be turning them "Into the edge" heel to toe, and you are normally using your dominant hand and flipping the razor to accomplish that..


Edit: Was just thinking about the circles.. I guess it could be possible that if you were turning into the edge on one side and away on the other you could be creating reversing Stria that might make one side slice better then the other while shaving but I am really reaching with that theory

The reason for the switching of hands was that before I was getting a very uneven edge. And instead of trying the same thing over and over, I tried something a little different. I assumed that I was lifting up or pushing down with a hand, so I did one round with each hand to avoid that un even edge.

I wasn't really paying attention to the direction of the circles either, I didn't think it would matter on that. I will try to reset the bevel tomorrow keeping all this in mind. I also re watched some of the videos so there will be a few things I will be doing differently as well, such as keeping my elbow up. Hopefully this all helps me get a better edge.

When I started honing my push stroke was much heavier than my pull stroke and resulted in deeper stria on the push side. Once I addressed that my bevels on the push side got much more consistent. May be related to your issue.

The closer side, the one you are less confident with...it might be a pressure issue with the gingerly wielded off hand versus the manly on hand...but gssixgun would be the man for honing issues. I can only throw spitballs and off speed pitches.
Good luck...generally, I would forget a shave to shave analysis and focus on the long game...and find someone to teach you honing...in person, if at all possible.

I woke up thinking about this post. I guess because I like math that doesn't involve numbers.
As far as one side of the razor being 'sharper' than the other, with the two sides of the face supporting this idea: in a normal two pass shave each side of the face receives both sides of the razor. Edge down first pass N-S, edge up, second pass S-N.
Additionally, I believe where the bevel meets is where sharp lives, at the tippy top of the triangle. To visualize this, think of the tippy top of the triangle created by the bevel. I don't think there is a 'side' to sharp, but I could easily be wrong. Any discussion that I have read on the Forum about bevels usually have to do with size or unevenness and never bring sharp into the equation (my razor shaves good but the bevel is ugly). To sum up, the two planes of the bevel do not have their own edge.
Bonus Input: If your spine is funny, your bevel will be funny. The way to correct funny is honing while riding a Tilt-A-Whirl.

I don't think it's possible for one side of the bevel to be sharper than the other. You can get different angles if the bevel is asymmetrical as with a kamisori grind - but, in my experience, that has never made a difference to how either side performs.

I'd say the differences you are experiencing one side to another is a lack of consistent technique - angle is very important with a straight and takes some time to nail properly.

Gotta go with Gsixxgun on this one. If the bevel meets in the middle it would be sharp, but if the bevel was offset to the spine axially it would take a different angle to achieve the same cutting action. Hope this makes sense, sorry for my poor explanation. Instead of being an isosceles triangle at the top of the bevel it would be slightly right angle one way or the other.

Originally Posted by JoeSomebody

Instead of being an isosceles triangle at the top of the bevel it would be slightly right angle one way or the other.

This is what I was thinking the issue was. The wife is going out tonight so I will spend some time in my cave that most call the basement trying to fix this. In the past I have tried just straight push and pull stroke on the 4/8k and have done circles. Are there any suggestions to which would work better?
The last time I used circles and got pretty good results. I am planning on doing that unless there is a better way. Here is what I was planning on doing:
- 20 circles per side with pressure on 4k
- 20 circles per side with little to no pressure on 4k
- 20 circles per side with no pressure on 8k
- 6 x strokes on 8k
- Finish with a good stropping (no CrOx, My strop is just 2 sided leather- suede and smooth)

Do More on 8k to smoothen it further. Just my 2c though :-)