Page 1 of 2 12 LastLast
Results 1 to 10 of 20

Thread: Fast cutters

  1. #1
    Loudmouth FiReSTaRT's Avatar
    Join Date
    Jun 2005
    Location
    Etobicoke, ON
    Posts
    7,171
    Thanked: 64

    Default Fast cutters

    I just spent like 4 hours trying to put an edge on an old and dull W&B with my japs. I'm getting there but it's still a b**** of a job. Therefore, I'd like to know what I can use as a fast cutter in the medium to fine grit range, to put that initial edge on the blade before I start doing the pyramids. Since I have 2 more blades to get into a shave ready condition (barring any new purchases) and are both extremely dull, I'd like to know what cuts quickly. Any ideas gentlemen?

    P.S. I heard that the coticules are fast cutters. Is that true or should I get something else?

  2. #2
    Senior Member Tony Miller's Avatar
    Join Date
    May 2005
    Location
    Nottingham, Maryland
    Posts
    2,559
    Thanked: 382

    Default

    The Japanese stones tend to be slow. I dont think the Belgian are tat fast either. A Norton is the fastest stone I know of.

    Tony
    The Heirloom Razor Strop Company / The Well Shaved Gentleman

    https://heirloomrazorstrop.com/

  3. #3
    Loudmouth FiReSTaRT's Avatar
    Join Date
    Jun 2005
    Location
    Etobicoke, ON
    Posts
    7,171
    Thanked: 64

    Default

    Thanks Tony. Would a lower grit cut faster than the 4k?

  4. #4
    Senior Member Tony Miller's Avatar
    Join Date
    May 2005
    Location
    Nottingham, Maryland
    Posts
    2,559
    Thanked: 382

    Default

    Bigger grit does not always mean faster cutting. The grit size (individual grains) determines the smoothness, the spacing of the grains determines how fast they cut. Some stones are very densly packed and are slow cutting. Other have some sopace between the fine grains (like a Norton 4K) and cut faster as there is free space, or relief between the grains.

    Tony
    The Heirloom Razor Strop Company / The Well Shaved Gentleman

    https://heirloomrazorstrop.com/

  5. #5
    Loudmouth FiReSTaRT's Avatar
    Join Date
    Jun 2005
    Location
    Etobicoke, ON
    Posts
    7,171
    Thanked: 64

    Default

    I guess I will have to eventually follow the herd. Next paycheque, I guess. Once again, thanks Tony. As for me, I'm checking out and flying off to lala-land. 'Night

  6. #6
    Super Shaver xman's Avatar
    Join Date
    May 2005
    Location
    Lotus Land, eh
    Posts
    8,194
    Thanked: 622

    Default

    You might try a few dozen passes on the 4k alone and see how that works. If you get teh sharp knife feeling from that then you can go on to the pyramid. Don't be tempted to go fast or add pressure to the blade either. That will just waste your time and you won't even learn anything useful except not to be hasty or add pressure.

    X

  7. #7
    Member AFDavis11's Avatar
    Join Date
    May 2005
    Location
    Virginia
    Posts
    5,726
    Thanked: 1486

    Default

    I've used 1K grit wet/dry sandpaper, wetted and placed on top of my Norton 8K edge. For a dollar a sheet its a pretty economical hone.

    A Norton 1K might be helpful, since you seem to enjoy honing so much.

    There are a lot of hones that are knife hones that you could use as well.

  8. #8
    Loudmouth FiReSTaRT's Avatar
    Join Date
    Jun 2005
    Location
    Etobicoke, ON
    Posts
    7,171
    Thanked: 64

    Default

    My post got lost for some reason. I was thinking of getting one of those Spyderco ceramic hones. Would that do the trick?

    The way I got this one close to being shave ready is by going circular w/ pressure on the bottom side of the 4k with the occasional pyramid just to see where I am. This was done for fast metal removal because the razor was really dull, so I needed to form the initial edge before going fine.

  9. #9
    Senior Member superfly's Avatar
    Join Date
    May 2005
    Location
    Toronto, ON
    Posts
    1,950
    Thanked: 16

    Default

    I also use 1000 grit sandpaper to restore edge fast. Just slap some with double stick tape onto some glass plate, and there you go, a DIY hone for a buck or so...

    Nenad

  10. #10
    Hones & Honing randydance062449's Avatar
    Join Date
    May 2005
    Location
    Saint Paul, Minnesota, United States
    Posts
    7,971
    Thanked: 2202
    Blog Entries
    1

    Default

    For the time being go with the sandpaper suggestion. Use either 1000,1200,1500 grit wet/dry and lay it on a wet jap hone. Go easy on the pressure because the sandpaper will cut fast. Check your edge frequently by using the thumbnail test.
    Be sure to wet the sandpaper, then you will not have to use any tape to hold the sandpaper down. It creates its own suction.

    Hope this helps,
    Randolph Tuttle, a SRP Mentor for residents of Minnesota & western Wisconsin

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •