Results 1 to 10 of 21
Thread: Oops... I dropped it!
Hybrid View
-
06-13-2016, 06:09 PM #1
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215How does it shave? That is all that counts.
If it is not scratching, you lucked out.
-
06-13-2016, 06:21 PM #2
Last edited by howdydave; 06-13-2016 at 06:24 PM.
Realization of the vastness of ones own ignorance is the first step on the path to true wisdom.
Dave N.
-
06-13-2016, 06:36 PM #3
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215Yes, bevel.
I meant, not scratching your face.
-
08-07-2016, 11:08 PM #4
- Join Date
- Apr 2015
- Location
- VERO BEACH, FL
- Posts
- 903
Thanked: 96CARPET SOLUTION
I have a throw rug by my sink in my bathroom just in case. The one place I did drop a razor was when I was honing it. Putting my stones away and heard the razor hit the floor I knew it was bad news. Put a nice nick on the blade edge which took some serious honing to correct. I now have a rubber mat on the floor by my work station. I also have a towel by the sink just to protect the razor when I put it down.
-
08-08-2016, 12:46 AM #5
- Join Date
- Oct 2005
- Location
- Winnipeg Manitoba Canada
- Posts
- 1,333
Thanked: 351If a gentle stropping on the canvas/linen side of a strop does not remove the spot, it's NOT a black spot from your black strop. Personally, when I see something like that on an edge when looking through my 40x cheapo loupe, I'll gently swipe across that edge with my clean thumb.... Hey, it's my thumb! I use the same motion as when stropping.... away from the edge.
I typically see those kinds of blackspots in older razors where there is pitting. If this is a brand new razor, it's not likely pitting, but rather an inclusion in the steel that has shown up. I would be shocked if it was a chip..... if it was a bur, it would be leaving obvious scratches in the surface of your strop.
Ultimately, if it doesn't bother you while shaving.... it's nothing to worry about, it will get removed the next time the razor is honed. I know it's considered "not done" in the world of straight shaving, but I shaved with a razor that had a few micro chips that did not bother me in the least, and I refused to waste the steel in the edge to remove them. I shaved with those microchips visible (there were 2 or 3 if I remember correctly) for nearly two years before they were removed completely in a honing session. I'd be the first to hone such things out if I could feel them during a shave, but if not... meh.
Consider yourself lucky, the last razor I accidentally knocked off the ledge into the bathtub lost it's entire edge... I spent hours honing that thing! I know some of you think it could have been worse, as in the blade breaking.... but nope, that would have saved me hours of honing, and I would have been all too happy!
It's easy to throw away a broken blade... a damaged blade on the other hand... well, gotta fix it... no matter how long it takes!
Edit: I should have included that *THIS* is why you need at least two razors, if one gets damaged for whatever reason, you always have your second one to keep you going while the damaged one gets fixed. You could also say "2 is 1 and 1 is none". ADAMHIKT
Regards
ChristianLast edited by kaptain_zero; 08-08-2016 at 12:50 AM.
"Aw nuts, now I can't remember what I forgot!" --- Kaptain "Champion of lost causes" Zero