Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Member
    Join Date
    Oct 2009
    Posts
    91
    Thanked: 12

    Default What to do with this razor?

    Often when bidding for a lot/box of straight razors if I am the high bidder I put them in a box..later open them up and check each one...and when I find a blade like this one, what would be something useful/helpful to do with one with a big chip in the blade like this one? Thanks
    Attached Images Attached Images  

  2. #2
    Know thyself holli4pirating's Avatar
    Join Date
    Feb 2008
    Location
    New York
    Posts
    11,930
    Thanked: 2559

    Default

    Since the blade doesn't have a shouder, that chip can be honed out with no problem. You'd also want to rescale it, because that pivot pin is not secure at all.

    I'd say set it aside unless these are things you are already comfortable doing, or send her out if you are so inclined to pay to have her fixed up.

  3. #3
    Senior Member AlanII's Avatar
    Join Date
    Apr 2008
    Posts
    1,689
    Thanked: 244

    Default

    +1 on, holli's post. What's the maker's name? Fine looking thing.

  4. #4
    Senior Member janivar123's Avatar
    Join Date
    Oct 2009
    Location
    Porsgrunn Norway
    Posts
    883
    Thanked: 173

    Default

    depend on what size it would end up if grinding it down
    or you could look at http://straightrazorpalace.com/shavi...hie-razor.html

  5. #5
    all your razor are belong to us red96ta's Avatar
    Join Date
    Sep 2009
    Location
    Fresno, CA
    Posts
    1,368
    Thanked: 446

    Default

    Yes, it can be saved....if it were mine, I'd retire it.

  6. #6
    what Dad calls me nun2sharp's Avatar
    Join Date
    Feb 2008
    Location
    Kansas city area USA
    Posts
    9,173
    Thanked: 1677

    Default

    It will take some work, as Dylan said.
    It is easier to fool people than to convince them they have been fooled. Twain

  7. #7
    Senior Member blabbermouth JimmyHAD's Avatar
    Join Date
    Feb 2008
    Posts
    32,564
    Thanked: 11042

    Default

    Quote Originally Posted by nun2sharp View Post
    It will take some work, as Dylan said.
    Unless it was a brand name I really wanted, had sentimental value, or I just wanted the practice I wouldn't mess with it.

    If I did I would probably hone it as I would a pocket knife with the spine off of the coarse hone until I got past the chip. Then throw a layer of tape on the spine and go to work with the spine on the hones. A razor maker or someone with more expertise and equipment than I've got could probably regrind the blade. Question becomes is it worth the labor to do it yourself or the $ to have it done. Only you can answer that.
    Be careful how you treat people on your way up, you may meet them again on your way back down.

  8. #8
    Member
    Join Date
    Oct 2009
    Posts
    91
    Thanked: 12

    Default

    The name on this razor is "J. R. Torrey Razor Co, Worcester, MASS"..think I'm just gonna put it back in my junk box....and leave it as is...Thanks to all for their suggestions...

  9. #9
    Connoisseur of steel Hawkeye5's Avatar
    Join Date
    Mar 2007
    Location
    Nashville, TN
    Posts
    937
    Thanked: 443

    Default

    Quote Originally Posted by Clockguy View Post
    The name on this razor is "J. R. Torrey Razor Co, Worcester, MASS"..think I'm just gonna put it back in my junk box....and leave it as is...Thanks to all for their suggestions...
    Well now wait just a second. Torry's are fine razors.

    I dare to say that it just depends on how much work you want to put into this razor, what you have for hones, and your blade width preference

    This is one of those "if, then" situations for someone that does not have the ability to regrind the blade (98% of us, probably more).

    And if you already have a DMT 325 diamond hone, and you are willing to spend the time (mucho).

    And if the final blade size will fall within an acceptable range for you.

    Then it may be worth the effort.

    But, if you don't have the hone or the time, or if the blade will end up too small I would pass.

  10. #10
    Senior Member simpleman's Avatar
    Join Date
    Sep 2010
    Posts
    361
    Thanked: 110

    Default

    Id hone the blade and fix the scales.

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •