Search:
Type: Posts; User: thp001; Keyword(s):
Search: Search took 0.01 seconds.
-
07-29-2021, 08:25 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
Finishing up some of the smaller razors, example...
Finishing up some of the smaller razors, example below. Waiting on some more horn for the big chopper, couldn't quite squeeze two scales out of the pieces I have.
334737
334738 -
07-13-2021, 10:56 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
Finishing the 10/8+ razor, spine, grob and barber...
Finishing the 10/8+ razor, spine, grob and barber notch taken to a full polish, tang and blade left in a glazed finish. For the polish I worked up through my selection of Trizact belts, ending at 5...
-
06-29-2021, 07:58 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
I'll have a bit more to post next week, been...
I'll have a bit more to post next week, been fairly busy recently since we are now haying our fields.
I did get some work done yesterday afternoon on a few of the wedge grind razors, all grinding... -
06-11-2021, 10:47 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
Yeah you need to leave it a bit thicker otherwise...
Yeah you need to leave it a bit thicker otherwise it's too flexible, I've only used it on two razors so far but have used it on quite a few knives since you have the tang as backing. The Warther...
-
06-11-2021, 06:48 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
It's hard to capture just how fine and even the...
It's hard to capture just how fine and even the Trizact finishes are. Also to note, this is a wedge grind (10 inch contact wheel) and the edge flexes under the thumb like a hollow. You want to grind...
-
06-11-2021, 06:34 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
I have a thread about the Masecraft Ivory in the...
I have a thread about the Masecraft Ivory in the workshop section. Shouldn't be too far down the list. There's a photo in there but it's pretty hard to capture the nuances, especially after polishing...
-
06-11-2021, 03:14 AM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
I use a museum grade artificial ivory from...
I use a museum grade artificial ivory from Masecraft called col.849 but I have some of the Dave Warther Resin Ivory on the way so I'll compare the two. Both are extremely visually accurate, the...
-
06-10-2021, 09:59 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
Took the hollow all the way back to make a...
Took the hollow all the way back to make a completely shoulderless grind. Been working on a batch of 5 7/8 razors, 4 wedges and this one hollow grind. Decided to freehand it and it came out good....
-
06-01-2021, 03:36 AM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
Yeah my weak side grinds were never as good so...
Yeah my weak side grinds were never as good so what I ended up doing is just flipping the blade on my strong side so that it is edge down. Works especially well on a full hollow because you're...
-
06-01-2021, 02:54 AM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
Are you using a jig? I use a homemade version of...
Are you using a jig? I use a homemade version of a knife grinding jig, I make my primary hollow then paint the blade with layout dye. I then scribe a line where the belly should land according to a...
-
05-31-2021, 09:46 PM
Thread: 7/8 Hollow grinding
by thp001- Replies
- 22
- Views
- 2,284
7/8 Hollow grinding
Working up this blade, a smiling full hollow, finished up the preliminary grinding before HT. Just need to drill the pivot, you really don't want to forget to do that before hardening!
332927...
Results 1 to 11 of 11