Results 1 to 9 of 9
Thread: Is this razor repairable?
-
06-22-2015, 04:51 PM #1
- Join Date
- Jun 2015
- Location
- Billings, Montana
- Posts
- 4
Thanked: 0Is this razor repairable?
-
06-22-2015, 05:00 PM #2
- Join Date
- Jan 2008
- Location
- Rochester, MN
- Posts
- 11,552
- Blog Entries
- 1
Thanked: 3795Yes, it does appear to be shallow surface rust and should easily be cleaned off. Now, some of the rust is on the etching so you will not be able to leave that intact.
The rust can be cleaned off with a series of w/d sandpaper grits. Just be careful of the edge.
Actually, since you are new, it might be best to pay someone to clean it up with a buffer and then hone it for you. That way you can start out with a good shaver.
-
The Following User Says Thank You to Utopian For This Useful Post:
outback (06-25-2015)
-
06-22-2015, 05:08 PM #3
- Join Date
- Jun 2015
- Location
- Billings, Montana
- Posts
- 4
Thanked: 0Ok. I was leaning toward having it done. It's a nice Dovo, not something I really want to learn and practice restoration with. I'd rather have it as one of my shavers. Any reputable restorers?
-
06-22-2015, 05:31 PM #4
Check the classifieds, Member Services area for some one close / you like. You can always reach out to them via pm if you have questions. It would help to add your location to your profile. Someone might reach out to help you if they know you are close.
Fuit radere viam antique masculum.
-
The Following User Says Thank You to stove For This Useful Post:
outback (06-25-2015)
-
06-22-2015, 05:36 PM #5
- Join Date
- Jun 2015
- Location
- Billings, Montana
- Posts
- 4
Thanked: 0Ok. Updating profile. Thanks for the help.
-
06-22-2015, 07:10 PM #6
- Join Date
- Apr 2012
- Location
- Diamond Bar, CA
- Posts
- 6,553
Thanked: 3215Yes, but it is going to take some work and be very careful work, not to lose too much the gold or the etch, but it can be done. You will lose the gold on the spine.
Start with a single edge razor blade and cut off all the active rust, then some 000 steel wool to see how deep the pitting.
Then some 600 and go from there, tape the gold and etch to protect it.
If you lose too much of the etch or gold, unpin and just buff it.
Or as said send it out. Condition is everything when buying a razor, if it needs repair, factor that into your cost. In the 70-100 range you can buy some very nice, shave ready vintage razors, check the classifieds.
-
The Following User Says Thank You to Euclid440 For This Useful Post:
outback (06-25-2015)
-
06-23-2015, 08:21 AM #7
I would take all of the above advice. There are some good deals in the classifieds on here most of the time & if you wait, it will be gone before you know it. If you see something you like, ask about it or look 'em up on eBay to see what they are going for on there but many if it is a bin will be over priced. Sometimes you can get lucky but it is best to get advice also. You did good by asking.
-
06-23-2015, 02:36 PM #8
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 27,033
- Blog Entries
- 1
Thanked: 13247Pretty honest seller there IMHO, he actually went out of his way to show the worst parts of the blade and the rust with his pics... Unusual for e-bay any more
-
06-23-2015, 06:39 PM #9