The Butchered Blade

Well, I am working on something a bit different. I am yanking all of my horn-scaled razors which seem to never stay tight and won't center worth a damn and unpinning the tops, doing away with the spacers. Done 4 so far and it cured all of them.
The tang has to center the blade in the scales and the spacers dampen the effect. Plus, Horn-on-tang is nice and tight instead of horn on the little spacer. This one has Babur's collars with bigs n' littles brass domes, using bronze rod. Managed to save the collars and domes!

Attachment 212287Attachment 212288

Quote:

---

Originally Posted by MikeB52

That would be very thoughtful, and appreciated Steve-O..
Thanks.
Great interesting link on finishes Euclid, thanks for posting that as well.

---

Mike I found them & they are new because the pivot hole isn't even drilled in them yet. If I remember right I have 2 of these so there's another one somewhere. This one was looking poor so I sanded them a little bit & they came back to life. They were scratched up & the Dorko badge was very dull looking but after a little sanding & polishing with some Maas. They look great but if you get them, I would unpin them & sand the rear scale smooth because as you see in the pics, it appears pitted or not made just right. They have your name on 'em unless I find the other set & they are better. I'll give you the better of the two.

Attachment 212295

Attachment 212296

[QUOTE=sharptonn;1542445]Well, I am working on something a bit different. I am yanking all of my horn-scaled razors which seem to never stay tight and won't center worth a damn and unpinning the tops, doing away with the spacers. Done 4 so far and it cured all of them.
The tang has to center the blade in the scales and the spacers dampen the effect. Plus, Horn-on-tang is nice and tight instead of horn on the little spacer. This one has Babur's collars with bigs n' littles brass domes, using bronze rod. Managed to save the collars and domes!


Good job Tom! I have found the same issue on some straights as well. I guess that's why a lot of old straight's, especially Sheffield razors don't use 'em.

Yep. Seems obvious to me now! As many as I have, I may be unpinning some more along the way!

Quote:

---

Originally Posted by MikeB52

Finished my Brookes up last night.
Left some divots on the sides out of the edge area so not an issue. Finished on that thuri it's resting on.
Honed up slowly, hard steel there. Ends up just shy of 7/8th.
Attachment 212257Attachment 212258
:chapeau

---

Ha cha cha chaa.!!
Looks god ....... Sweet mike

Quote:

---

Originally Posted by sharptonn

Yep. Seems obvious to me now! As many as I have, I may be unpinning some more along the way!

---

Strange isn't it Tom? I have noticed that quite a few times.

MikeB52, I found the other set of scales but they have a scratch near the badge, yet the other scale doesn't have the abnormalities like the first set. You would have to be very careful sanding that scratch out near the badge. You wouldn't want to sand the badge too much & wear it down.

Attachment 212297

Attachment 212298

Actually, I could be a true gentleman & sand them out for ya. I could probably make the second set look a lot better once I get the scratch out.

Hey everyone.
Cleaned up a blade with etching on it. It was pretty faint when i started.
But to preserve it i tried something.
I scotch taped over it, then carefully cut the excess tape away from the perimeter. Thought to myself if the blade around it was nice and clean, it would be more visible.
It worked for the most part.
Attachment 212305Attachment 212306Attachment 212307Attachment 212308
So what ya think.?
I did with what i had......
The last two pics are after i removed the tape

Wow! I have never seen a German Elliott?

Wait! I seem to have 2 ofem! :roflmao

I have not looked for any info on it.
Really!!! Tell me more about what you know!!!

Here's a pic from the other side.
Attachment 212311