Results 1 to 8 of 8
Like Tree5Likes
  • 1 Post By MW76
  • 1 Post By Crawler
  • 3 Post By DoughBoy68

Thread: Naval jelly?

  1. #1
    Senior Member
    Join Date
    Feb 2016
    Location
    Pittsburgh, PA
    Posts
    171
    Thanked: 17

    Default Naval jelly?

    Anyone use naval jelly to remove rust for restores, and if so how has it worked? Any suggestions?

  2. #2
    Senior Member blabbermouth outback's Avatar
    Join Date
    Mar 2015
    Location
    Akron, Ohio
    Posts
    12,056
    Thanked: 4312

    Default

    Couple times...naah don't care for it. A single edge razor blade works best for me.
    Mike

  3. #3
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,436
    Thanked: 4827

    Default

    I tried it on the first couple of blades I worked on and I do not think it is worth using. It discolors the metal and you wind up having to do exactly the same amount of sanding to get the pitting out. My current method is a single edge razor blade, then clean up with steel wool and asses to see where I go next. Sometimes I just polish up and hone other times it is a tear down and hand sanding. The blade helps me decide.
    It's not what you know, it's who you take fishing!

  4. #4
    Matt MW76's Avatar
    Join Date
    Dec 2015
    Location
    Albany, NY
    Posts
    971
    Thanked: 260

    Default

    I think evaporust is a better alternative if your looking for a liquid rust remover.
    Crawler likes this.

  5. The Following User Says Thank You to MW76 For This Useful Post:

    Hirlau (09-05-2016)

  6. #5
    Senior Member Crawler's Avatar
    Join Date
    Jan 2015
    Location
    N.E. Indiana
    Posts
    970
    Thanked: 134

    Default

    Quote Originally Posted by MW76 View Post
    I think evaporust is a better alternative if your looking for a liquid rust remover.
    +1 for Evaporust! I've used it, including a thread I did looking for information on it. Look/search for "A ? Or Two on Evaporust?" here in the workshop. At least, I think that's the title of the thread.

    It can only do so much. You will still need to sand the blade.
    MW76 likes this.
    Decades away from full-beard growing abilities.

  7. #6
    Senior Member DoughBoy68's Avatar
    Join Date
    Sep 2008
    Location
    Crossville, TN
    Posts
    1,711
    Thanked: 304

    Default

    A tip I picked up a few years ago was take a piece of Aluminum foil crumple up, moisten it and rub the blade to remove rust. It is soft enough to not scratch the blade plus causes a chemical reaction that helps remove the rust. Might be something to try after scraping off the worst of the rust with a DE blade. If blade is not deeply pitted some good metal polish should finish the job.
    outback, MW76 and hrfdez like this.
    "If You Knew Half of What I Forgot You Would Be An Idiot" - by DoughBoy68

  8. #7
    Senior Member blabbermouth outback's Avatar
    Join Date
    Mar 2015
    Location
    Akron, Ohio
    Posts
    12,056
    Thanked: 4312

    Default

    Quote Originally Posted by DoughBoy68 View Post
    A tip I picked up a few years ago was take a piece of Aluminum foil crumple up, moisten it and rub the blade to remove rust. It is soft enough to not scratch the blade plus causes a chemical reaction that helps remove the rust. Might be something to try after scraping off the worst of the rust with a DE blade. If blade is not deeply pitted some good metal polish should finish the job.
    I'll have to try it sometime, thanks.
    Mike

  9. #8
    Senior Member
    Join Date
    Feb 2016
    Location
    Pittsburgh, PA
    Posts
    171
    Thanked: 17

    Default

    Thanks for the feedback gents, I do remember naval jelly leaving like a dull powdery kind of mess of the surrounding metal, would rather not do that to my razor.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •