Page 3 of 8 FirstFirst 1234567 ... LastLast
Results 21 to 30 of 79
Like Tree111Likes

Thread: Greaseless polishing compound?

  1. #21
    Skeptical Member Gasman's Avatar
    Join Date
    Nov 2016
    Location
    Colorado Springs
    Posts
    10,473
    Thanked: 2182

    Default

    How about the Glu-tite wheel prep? Is this something that is needed? Guess it helps the compound stick to the wheels?

    And Caswell has some blue and white polishing bars. Are they worth getting? The white does a little cutting and blue just polishes to shine. I Think!

    Comments?
    Last edited by Gasman; 02-15-2017 at 08:58 PM.
    It's just Sharpening, right?
    Jerry...

  2. #22
    Senior Member
    Join Date
    Jul 2016
    Location
    Addison Michigan
    Posts
    627
    Thanked: 115

    Default

    Hey I get all my stuff at Eastwoods If that Helps Any,, Nice Looking Buffer,,Ty
    Gasman likes this.

  3. The Following User Says Thank You to Addison For This Useful Post:

    Gasman (02-16-2017)

  4. #23
    Senior Member blabbermouth
    Join Date
    Apr 2012
    Location
    Diamond Bar, CA
    Posts
    6,553
    Thanked: 3215

    Default

    Have the gluetite, but don’t use it, you don’t need it.

    The greased compounds I use most are Brown/Tripoli Green/stainless and White or blue for final. You need to make the jump from 600 to polish, Black or Brown to green, then white or blue.

    Castwell’s has a good chart.

    There are all kinds of other compounds that are combinations, like Black Magic, Fabuluster, Zam and some of the Castwells whites, you really have to try them, everybody has their favorites.

    Another thing that works well is a clean lose 6 inch wheel for final buffing, really makes it pop, after dusting with talc, to wick off the grease.
    Gasman likes this.

  5. The Following User Says Thank You to Euclid440 For This Useful Post:

    Gasman (02-16-2017)

  6. #24
    Senior Member kelbro's Avatar
    Join Date
    May 2008
    Location
    N. Carolina
    Posts
    1,352
    Thanked: 181

    Default

    I turn mine around and work off the top and back side of the wheel. Blade edge facing away. I can see better and better manage angles that way. But then, I am left handed and do most everything bass-ackwards LOL.
    RezDog, Dieseld and Gasman like this.

  7. The Following User Says Thank You to kelbro For This Useful Post:

    Gasman (02-15-2017)

  8. #25
    Senior Member blabbermouth RezDog's Avatar
    Join Date
    Feb 2013
    Location
    Haida Gwaii, British Columbia, Canada
    Posts
    14,383
    Thanked: 4820

    Default

    I have to say that if I could run mine the other way and work off the top of the wheel but still have the shut off switch facing me I would do it in a heart beat. The part I really don't like about turning the machine around is having to reach and fumble for the switch. Incidentally I am backasswards handed too. I have thought about using an electric motor with and extension and a buffing wheel just to het the top grinding action but having a closely located switch. All things in good time. No sense farmering everything up all at once.
    Gasman likes this.
    It's not what you know, it's who you take fishing!

  9. #26
    Senior Member blabbermouth
    Join Date
    Apr 2012
    Location
    Diamond Bar, CA
    Posts
    6,553
    Thanked: 3215

    Default

    There are many ways to buff, a lot depends on what your goal is and what you are starting with.

    I have all the grits of greaseless and boxes of greased. Most of the razors I buff are not in that bad of shape and would be considered clean up.
    Typically, I start with 600 greaseless, I keep 3 wheels of 600, full load, half and almost nothing. I rotate them and when I load the almost nothing wheel, the others move up in the progression. The almost nothing is great for clean-up especially cleaning Jimps, but that takes the grit out of the wheel fast, all the edges eat the grit, so do those last.

    If it needs more, I will go to 400, then hand sanding if needed. It is amazing what a little hand sanding will do to a finish, even 1 or 2k.
    Then I go to green greased, sometimes Tripoli then green then white. Hand polish and buff on a loose clean wheel with talc. I use Green the most of all the greased compound and buy the big sticks.

    When I load, I cover the wheel with a cereal box and load with the edge of the stick, greased or greaseless and run the stick across the wheel like a lathe chisel. Rotate the stick 90 degrees so you have a fresh edge.
    For greased you don’t need much, for greaseless run it across the face on way then back. Let the wheel run for a minute or two then apply another coat and let it dry fully.

    When using greased and it starts to load up on the razor, rake the wheel and re load. Pins will make the wheel load, so do those last.

    Black Magic works well after a light 600 wheel for scales, sometimes the blue works well on plastics and horn.

    You really have to experiment a lot depends on the pressure you use and how much prep you do to get the finish you want.
    Do Buy a wheel rake and rake your greased wheels, when new rake the wheels then stop the wheel and trim all the long threads with a sharp pair of scissors. If you don’t the threads will ruin your finish.

    If I was to start over, I would buy a HF buffer, 400 & 600 greaseless, and a set of small stick, black, brown, green and white greased, 2 wheels for each, 4 in sewn and a couple 6 in sewn and 6 in loose. I like the finish on the green with a 6 in wheel, think they need a little more speed. I like Castwells greased, but have other brands also.

    Then add as needed.
    Gasman likes this.

  10. The Following 2 Users Say Thank You to Euclid440 For This Useful Post:

    cwomg (02-28-2018), Gasman (02-16-2017)

  11. #27
    Skeptical Member Gasman's Avatar
    Join Date
    Nov 2016
    Location
    Colorado Springs
    Posts
    10,473
    Thanked: 2182

    Default

    Quote Originally Posted by kelbro View Post
    I turn mine around and work off the top and back side of the wheel. Blade edge facing away. I can see better and better manage angles that way. But then, I am left handed and do most everything bass-ackwards LOL.
    Thanks for that hint. I too am in my right mind.
    I'll see if this helps me too.
    It's just Sharpening, right?
    Jerry...

  12. #28
    Moderator rolodave's Avatar
    Join Date
    Aug 2011
    Location
    Racine, WI USA
    Posts
    7,530
    Thanked: 1927
    Blog Entries
    1

    Default

    The greaseless will dry. Keep the tubes in zip lock bags. I keep the bags in a fridge when not in use.

    I don't use mine a lot. Too many bad things can happen.

    But, when needed, they are very handy.
    If you don't care where you are, you are not lost.

  13. #29
    Skeptical Member Gasman's Avatar
    Join Date
    Nov 2016
    Location
    Colorado Springs
    Posts
    10,473
    Thanked: 2182

    Default

    In the fridge? I dont know if the wife would go for that in her fridge. I'll just have to seal them up and keep in my shack. Its always warm anyhow.

    Thanks for the details Euclid. Im still kicking around some ideas on what to buy but ill get something ordered today. Hope they can get stuff shipped in a week as id love to give this a go next week. And this will give me a chance to make some kind of stand to use outside. Cut down on the mess in my garage that the wife vacuumes and dusts. Crazy old lady but i love her. And my house is always spotless so i shouldnt complain.

    Now if anyone else want to post up the materials they use, im still watching. The more info i get the better chance ill have of having the right steps of stuff.
    It's just Sharpening, right?
    Jerry...

  14. #30
    Senior Member
    Join Date
    Jul 2016
    Location
    Addison Michigan
    Posts
    627
    Thanked: 115

    Default

    Yes fridge too warm they kinda, I would say melt down for no better of a word, kinda turn soupy, wont stick on wheel, i learned that the hard way, Ty

Page 3 of 8 FirstFirst 1234567 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •