Page 1 of 2 12 LastLast
Results 1 to 10 of 20

Thread: Walnut Bengal

  1. #1
    Senior Member garythepenman's Avatar
    Join Date
    Apr 2006
    Location
    Middle Earth, Just round the corner from Hobbiton, New Zealand
    Posts
    1,201
    Thanked: 8

    Default Walnut Bengal

    I've just finished my first set of scales with liners. I must sing praises of Bill Ellis's Blog for assistance. Hurraaayyyyyyy....Thanks for all of your efforts in setting that up and sharing Bill.

    I don't think the scales (walnut) needed much support but I wanted to do thin wood, thinner brass sheet and a red plastic liner and keep the whole lot flat sided.

    The blade was a rusty old Bengal 6/8 which has had some heavy wet/dry work and now needs some honing and stropping etc..

    I'm very pleased with the outcome, my best efforts to date for sure. I even made the spacer out of brass (bloody hard work).

    The wood has been well coated with dutch oil, dried and buffed up with 0000 grade steel wool. Then a coat of Briwax antique wood polish for a nice gloss and extra proofing.

    Gary
    Attached Images Attached Images    

  2. #2
    Vlad the Impaler LX_Emergency's Avatar
    Join Date
    Mar 2006
    Location
    Oss, the Netherlands
    Posts
    2,854
    Thanked: 223

    Default

    you're really getting into this aren't you? Good job though.

  3. #3
    Senior Member
    Join Date
    Apr 2006
    Posts
    460
    Thanked: 2

    Default

    Very nice. The wood gives the razor a vary classic feel but the metal, red liner combo lends the piece a modern edge. I think it all works well together.

  4. #4
    Vlad the Impaler LX_Emergency's Avatar
    Join Date
    Mar 2006
    Location
    Oss, the Netherlands
    Posts
    2,854
    Thanked: 223

    Default

    I hadn't really noticed the lining yet....but my goodness. You're turning into a little Vlad....

  5. #5
    Senior Member garythepenman's Avatar
    Join Date
    Apr 2006
    Location
    Middle Earth, Just round the corner from Hobbiton, New Zealand
    Posts
    1,201
    Thanked: 8

    Default

    Thanks for the compliment LX but Vlad is a true master at this.
    I'm still in the early stages of the disease.

    Gary

  6. #6
    Vlad the Impaler LX_Emergency's Avatar
    Join Date
    Mar 2006
    Location
    Oss, the Netherlands
    Posts
    2,854
    Thanked: 223

    Default

    Gotta start somewhere
    I'm going to try a little original scale making myself soon. As soon as i get the blanks that Vlad sent me as a matter of fact. I'm not quite sure yet what I'm going to do But I have a few idea's and might have an original trick or two up my sleeve. I just hope I can pull it off.

  7. #7
    Senior Member garythepenman's Avatar
    Join Date
    Apr 2006
    Location
    Middle Earth, Just round the corner from Hobbiton, New Zealand
    Posts
    1,201
    Thanked: 8

    Default

    Well LX, I say go for it.

    I must admit to having wasted a few nice pieces of wood and numerous brass pins and washers.

    My advice is to try it on some ordinary stuff first then go for it. You soon learn a few tricks and processes that make life easier.

    Post your efforts of course.

    Gary

  8. #8
    Member
    Join Date
    Apr 2006
    Posts
    69
    Thanked: 0

    Default

    Very pretty work! I like the way the red brings out the similar tones in the walnut.

  9. #9
    Member kyle's Avatar
    Join Date
    May 2006
    Location
    Texas
    Posts
    35
    Thanked: 0

    Default

    Very nice, Gary.

  10. #10
    Super Shaver xman's Avatar
    Join Date
    May 2005
    Location
    Lotus Land, eh
    Posts
    8,194
    Thanked: 622

    Default

    Very sweet. You've got excellent taste in scale material.

    No offense intended, but the scales you are making look a little on the chunky side. May I ask your reasoning behind this? Is it a practical or ęsthetic decision?

    X

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •