Results 1 to 6 of 6
  1. 01-02-2011, 10:05 PM #1
    chris21908
    chris21908 is offline
    Member
    Join Date
    Nov 2009
    Posts
    80
    Thanked: 11

    Default round to spike point?

    has anyone tried this? i have a gold dollar and was just curious about possibly turning it into a spike point. any tips or suggestion?
    Reply With Quote Reply With Quote
  2. 01-03-2011, 12:07 AM #2
    markevens
    markevens is offline
    Still learning markevens's Avatar
    Join Date
    Jun 2010
    Posts
    1,043
    Thanked: 240

    Default

    Don't do it. Noreason to ruin a perfectly good razor. If you want a spike point, there are plenty to be had at a very reasonable cost in the classifieds, via whipped dog, or the restored razor.
    Reply With Quote Reply With Quote
  3. 01-03-2011, 12:58 AM #3
    holli4pirating
    holli4pirating is offline
    Know thyself holli4pirating's Avatar
    Join Date
    Feb 2008
    Location
    New York
    Posts
    11,930
    Thanked: 2559

    Default

    Sure, you can do it if you want to. Personally, I would rather just buy a razor with the point I want rather than modding one, but it's your choice. Keep the speed/heat low and go slowly. Make sure you observe all safety percautions as well.
    Reply With Quote Reply With Quote
  4. 01-03-2011, 01:37 AM #4
    ndw76
    ndw76 is offline
    The only straight man in Thailand ndw76's Avatar
    Join Date
    Jan 2009
    Location
    Bangkok, Thailand
    Posts
    1,659
    Thanked: 235

    Default

    I have done this to a razor which has been serverly chipped at the toe. It takes a long time and to make it look astheticly pleasing you will also have to shorten the scales.

    All up I think it would be much easier and more fun to just buy a spike point razor.
    Reply With Quote Reply With Quote
  5. 01-03-2011, 01:46 AM #5
    niftyshaving
    niftyshaving is offline
    Senior Member blabbermouth niftyshaving's Avatar
    Join Date
    Oct 2009
    Location
    Silicon Valley, CA, USA
    Posts
    3,157
    Thanked: 852

    Default

    Quote Originally Posted by holli4pirating View Post
    Sure, you can do it if you want to. Personally, I would rather just buy a razor with the point I want rather than modding one, but it's your choice. Keep the speed/heat low and go slowly. Make sure you observe all safety percautions as well.
    +1
    Grinding hard steel is difficult and beginner folk often resort to
    power tools when they should not. Heat will wreck the steel or if
    it catches you have a flying razor that can hurt you
    or a bystander. SAFETY, SAFETY.

    You may take a coarse hand stone and give the nose
    ten min of attention on a Sunday afternoon. After
    a month of Sundays you will have a spike. If you
    rush it you risk damage. Razor steel is brittle like
    glass on some razors.

    This is one of those "can I", "may I" questions.
    Yes you may, it is your razor.
    Can you... only you know how handy you are.

    I would advise you to watch the Classified...
    Spike points do show up.
    Reply With Quote Reply With Quote
  6. 01-04-2011, 06:57 AM #6
    chris21908
    chris21908 is offline
    Member
    Join Date
    Nov 2009
    Posts
    80
    Thanked: 11

    Default

    Quote Originally Posted by ndw76 View Post
    I have done this to a razor which has been serverly chipped at the toe. It takes a long time and to make it look astheticly pleasing you will also have to shorten the scales.

    All up I think it would be much easier and more fun to just buy a spike point razor.
    i was actually wondering about the possibility of chipping the toe. i wouldn't want that to happen! i would probably pass on this idea then it would be better to just buy a new razor
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules