Results 1 to 7 of 7
  1. #1
    Senior Member 96firephoenix's Avatar
    Join Date
    Jul 2011
    Location
    Indianapolis, IN, USA
    Posts
    179
    Thanked: 9

    Default electrolyisis rust removal on a straight razor?

    so my dad has this big electrolysis vat in the basement that he uses for pulling rust off of tools he buys at auctions. it does a damn good job, but I don't know if it is suitable for straight razors.

    I'd have to ask for sure to remember how it works, but I'll outline the basics. You make a solution of washing soda (basic, I think - as opposed to acidic) and then attach a positive lead to your piece and a negative lead to an anode in the solution (could be the other way around) The electrical current and the solution pull the rust off the piece and onto the anode.

    would this work on a straight razor for rust removal?

  2. #2
    This is not my actual head. HNSB's Avatar
    Join Date
    Nov 2009
    Location
    Middle of nowhere, Minnesota
    Posts
    4,623
    Thanked: 1371
    Blog Entries
    2

    Default

    You might want to read this thread: http://straightrazorpalace.com/works...ctrolysis.html
    You can just read this post if you're short on time: http://straightrazorpalace.com/works...tml#post209743

    There are a few other threads on it as well. Basically, a few guys have done it, but the results were less than stellar.
    There will be oxidation to sand off after the electrolysis, and it still doesn't do anything about the pitting.

    Strange women lying in ponds distributing swords is no basis for a system of government.

  3. #3
    Senior Member
    Join Date
    Mar 2011
    Location
    Corcoran, Minnesota
    Posts
    665
    Thanked: 170

    Default

    I tried it. I used a battery charger for a power source. WAY too much amperage. Basically, burned up the razor - it was a complete junker, so no loss. If you try it, use a very low power battery for a power source. Possibly a little 9 volt? Don't try it on anything but a junk blade. The process is great for old hand tools, but my experience was not for razors.

  4. #4
    Senior Member 96firephoenix's Avatar
    Join Date
    Jul 2011
    Location
    Indianapolis, IN, USA
    Posts
    179
    Thanked: 9

    Default

    Quote Originally Posted by HNSB View Post
    You might want to read this thread: http://straightrazorpalace.com/works...ctrolysis.html
    You can just read this post if you're short on time: http://straightrazorpalace.com/works...tml#post209743

    There are a few other threads on it as well. Basically, a few guys have done it, but the results were less than stellar.
    There will be oxidation to sand off after the electrolysis, and it still doesn't do anything about the pitting.
    I must have mis-typed it in the search bar, cuz I didn't find anything.

    I kinda figured this would be the result.

  5. #5
    Lookin like a crim baldy's Avatar
    Join Date
    Apr 2009
    Location
    Coffs Harbour Australia, Home of the Big Banana
    Posts
    2,706
    Thanked: 1072

    Default

    The word Electroloysis in the above post is a link, just click on it.
    Grant
    "I aint like that no more...my wife, she cured me of drinking and wickedness"
    Clint Eastwood as William Munny in Unforgiven

  6. #6
    Senior Member 96firephoenix's Avatar
    Join Date
    Jul 2011
    Location
    Indianapolis, IN, USA
    Posts
    179
    Thanked: 9

    Default

    Quote Originally Posted by baldy View Post
    The word Electroloysis in the above post is a link, just click on it.
    Grant
    I did. I meant that when I searched before starting this thread, I must have mistyped it and that I thought the results would be "don't do it."

  7. #7
    Senior Member Caledonian's Avatar
    Join Date
    May 2011
    Location
    Saudi Arabia and Scotland
    Posts
    314
    Thanked: 60

    Default

    I'm sure that in some circumstances it will work very well. But why? There are chemical rust removers which will work just as well on an item this size. They will leave the pitting to be sanded away, and there is a possibility of a slightly roughened finish, so you have to watch them keenly in action. But this applies to electrolysis too, and especially to improvised methods of electrolysis.

    As has been said, too much current can pit the steel on its own. I think it will be like plating, in which what counts is the ratio of current supplied, to surface area of the workpiece. A razor is a lot smaller than most tools.

    While I don't have any scientific basis for this, I would be very wary - not just a little, but very - of different metals in a conducting solution, especially when electricity is supplied. If you do try this, the razor should be hung on steel wire, in a plastic, enamelled or glass vessel.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •