Results 1 to 10 of 24
-
01-30-2012, 06:36 AM #1
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 26,987
- Blog Entries
- 1
Thanked: 13234One Piece Scales - Problems and Solutions
So after making my first set of one piece scales
I was working through a set today for a rather large tanged W&B this one has a nearly 1/4 inch thick tang so now the problems with a set of one piece scales rises it's ugly head...
I looked through SRP and found that the problem has come up before with some solutions
1. Cut the slot at two angles to create the "flair" at the pivot end
2. Use wider material and a wider Kerf blade to cut the razor slot
3. Use a band saw and cut the "flair" into the scales.
Although these solutions can work they leave me wanting a neater cleaner look
So how to create a flair like from a wedge yet not have the ability to make the wedge
I wanted a nice even straight cut with equal thickness on the sides of the scales, so this is my solution to the problem..
I put in a wedgesorta
I made a wedge out of acrylic, after the scales were shaped, sanded, and cut, so basically they would be ready for a smaller tanged razor, but with out the coats of final finish.. I pushed the wedge down into the razor slot as far as I could, it was about 1 inch shy of the end.. I took this and placed it over a boiling pot of water on top on a splatter screen so it was right in the steam.. After about 3 minutes I pushed the wedge deeper, and put it back in the steam, another 3 minutes and the wedge hit bottom... I left the whole thing in the steam for about 5 more minutes, I let it cool completely and this is where I am at now.. It looks like steam shaping might be working.
The flair is there just like a two piece set of scales, I'll put it all together tomorrow and see how the fit works...
Hopefully the flair will stay "set" in the wood to create a bowed effect that I am after.Last edited by gssixgun; 01-30-2012 at 02:58 PM.
-
The Following 9 Users Say Thank You to gssixgun For This Useful Post:
BKratchmer (01-31-2012), cudarunner (07-18-2012), DoughBoy68 (12-12-2020), Laurens (03-21-2013), lz6 (01-31-2012), RayCover (01-31-2012), ScottGoodman (01-30-2012), skipnord (03-21-2013), WillN (02-02-2012)
-
01-30-2012, 06:50 AM #2
Very interesting! can wait to see the results after pinning - have always wanted some one piece scales...
-
01-30-2012, 03:43 PM #3
- Join Date
- Mar 2011
- Location
- Corcoran, Minnesota
- Posts
- 665
Thanked: 170There may be a bit of spring back as it dries, but with my experience long ago with bending snowshoes, I am betting your method will work. Looking forward to seeing the finished product. Thanks for posting this.
-
01-31-2012, 01:53 AM #4
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 26,987
- Blog Entries
- 1
Thanked: 13234Second day
I tried out the fit from yesterday's attempt, and there was a good improvment but I figured that it could get better..
I re-adjusted the wedge a bit on the grinder then re-steamed it and used so cut down toothpicks to adjust the flair a bit more.
I was pleased enough with the outcome to go ahead and apply some Teak oil finish, I figured nif I still don't like the fit after this I will add a 3rd pin..
BTW the scales are Bolivian Rosewood
-
01-31-2012, 03:40 AM #5
Very clever! I have used a mitre gauge and done two cuts on the scales before, but it takes a lot of work to get it set right for the kind of perfect result guys like us crave... especially trying to get the top-to-bottom taper too...!! Leaves something to be desired in the safety department as well-- lot of blade and throwing power on a 10" tablesaw for something to small.
I'm going to try this out...
-
01-31-2012, 04:10 AM #6
Glen,
Did you put any kind of clamp on the "wedge" to protect it from splitting while you were wedging it?
-
01-31-2012, 04:34 AM #7
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 26,987
- Blog Entries
- 1
Thanked: 13234
-
01-31-2012, 04:37 AM #8
- Join Date
- Jun 2007
- Location
- North Idaho Redoubt
- Posts
- 26,987
- Blog Entries
- 1
Thanked: 13234
-
01-31-2012, 04:55 AM #9
Thats what I was thinking Glen. Just as a safety net. That end grain is getting pretty short back there.
Great Idea BTW, I like that method for two reasons. 1> you can use a smaller block of material to begin with and 2> You don't have to expose end grain that may feather or even break on some woods by making a V cut wide enough to get the job done. Good job using your noggin there.
-
01-31-2012, 04:58 AM #10