Page 1 of 2 12 LastLast
Results 1 to 10 of 15
Like Tree8Likes

Thread: Tips for finishing scales in sliky smooth, high gloss surface? Okay to polish shank?

  1. #1
    Junior Member
    Join Date
    Jan 2012
    Posts
    13
    Thanked: 3

    Default Tips for finishing scales in sliky smooth, high gloss surface? Okay to polish shank?

    I've decided to make my own scales out of madrone wood from my family's ranch and did a trial run on a piece of mesquite I harvested from my back yard. I'm wanting to finish the scales in a smooth, high gloss finish and was wondering what the best way is to do this. Shellac vs. polyurethane? Apply one coat, sand, and apply again, over and over? Any tips would be greatly appreciated.

    Also, the razor is a Dovo Best Quality that has a polished blade but the shank and tang are not polished. Is it okay to polish these parts to a high shine? I was planning on using a Dremel with jeweler's rouge on a felt polishing wheel.

    Below is my first attempt with mesquite. I used a chop saw (only suitable piece of equipment I have available) to cut flat pieces, then did the rest by hand with a coping saw and sand paper.

    Name:  IMG_7949.jpg
Views: 966
Size:  51.9 KB

    This video from Lewis Razors was my inspiration to start this project: making straight razor scales with a minimum amount of hand tools - YouTube


    Thanks for any help!
    spazola likes this.

  • The Following 3 Users Say Thank You to Flatland2D For This Useful Post:

    Cove5440 (05-28-2012), David52 (05-28-2012), spazola (05-28-2012)

  • #2
    the deepest roots TwistedOak's Avatar
    Join Date
    Feb 2011
    Location
    Seattle
    Posts
    1,221
    Thanked: 169

    Default

    I think thin superglue (CA) yields some pretty high gloss results if you put enough coats on.

  • The Following User Says Thank You to TwistedOak For This Useful Post:

    Flatland2D (05-28-2012)

  • #3
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    I did a bit of reading on Madrone wood as I had never worked it before, what most people where saying is it is similar to Walnut.. To me that means you can go just about any direction you want when it comes to finishing...
    Ease of use - Wipe on Poly, Teak Oil, Danish Oil
    Middle ground - Tung Oil, Polyurethane, Gunstock finishes
    More of a Challenge - CA, Epoxies, these are really easy once you have everything set up, but tuff the first time through

    For beauty it is hard to beat a well done Tung Oil finish or a CA finish

  • #4
    Senior Member blabbermouth
    Join Date
    Jul 2010
    Location
    Portland, OR
    Posts
    2,697
    Thanked: 830
    Blog Entries
    1

    Default

    Glen beat me to the CA recommendation, but in the process, also gave you the full context of the different approaches and the degree of difficulty. There's a reason we like him so much.

    I thought I saved the thread about his tips for CA finish, which I used for my first few scale projects, but naturally its nowhere to be found right now. Its worth searching for. 'Something like 'tips for using a CA finish'.

    The last one came out like this:
    Name:  IMGP1134.JPG
Views: 670
Size:  132.8 KB

    Have fun doing it. Each one you do will get better.

  • #5
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    That was a good thread, after tons of people added to it,, Good thought Rob

    It also gives an idea of all the steps involved with them

    http://straightrazorpalace.com/works...ints-tips.html

  • #6
    Junior Member
    Join Date
    Jan 2012
    Posts
    13
    Thanked: 3

    Default

    Thanks gssixgun for the CA suggestion. I found the thread in the sticky. Very detailed instructions. I'm looking forward to trying it out on some test pieces later.

    So there shouldn't be any problems with polishing the shank to a mirror finish?

    I'll post pics of my "upgraded" razor when I'm done with the new scales and polish. Might be a few weeks though.

    Thanks again to all!

  • #7
    At this point in time... gssixgun's Avatar
    Join Date
    Jun 2007
    Location
    North Idaho Redoubt
    Posts
    26,948
    Thanked: 13221
    Blog Entries
    1

    Default

    I always polish out the "shank" if the razor is out of the scales no sense in putting it back in with anything but clean bright steel...

    Just to clarify you are talking just polishing, no grinding on it right ???

  • #8
    Junior Member
    Join Date
    Jan 2012
    Posts
    13
    Thanked: 3

    Default

    Quote Originally Posted by gssixgun View Post
    I always polish out the "shank" if the razor is out of the scales no sense in putting it back in with anything but clean bright steel...

    Just to clarify you are talking just polishing, no grinding on it right ???
    Yes, just polishing to make it nice and shiny, no grinding.
    gssixgun likes this.

  • #9
    Member
    Join Date
    May 2012
    Location
    lawrence, ks
    Posts
    62
    Thanked: 6

    Default

    i use a fingernail buffing system to get my scales , brass pins and horn on razors and knives to a super smooth state. that way when a finish is applied it is that much smoother. the buffing block is just a dollar and is amazing works wounders on brass pins.
    Geezer likes this.

  • #10
    At Last, my Arm is Complete Again!! tinkersd's Avatar
    Join Date
    Dec 2008
    Posts
    550
    Thanked: 55

    Default

    I do remember the last Str8 I did, as I polished up the shank by using my Dremel tool 1st with brown emery, then with white tripoli, and finally with red jewelers' rouge.

    No photo's for you but it did turn out very nice I thought, FWIW.

    As every, tinkersd

  • Page 1 of 2 12 LastLast

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •