Page 1 of 11 12345 ... LastLast
Results 1 to 10 of 106
Like Tree74Likes

Thread: Wooden Scale Advice

  1. #1
    The Razor Talker parkerskouson's Avatar
    Join Date
    Jun 2012
    Location
    Las Vegas
    Posts
    623
    Thanked: 75

    Default Wooden Scale Advice

    Hey guys. So, just a preface, I have been reading the scale making section of the wiki so I've done some research. I want to make a pair of Walnut scales for my Geneva 5/8 hollow razor. The wood is plenty dry, been sitting in Vegas heat for 3 years. What would be the best way to start? I have plenty of tools, I just more or less need some do's and don'ts as I've never done this before!

    Let me know what you think!

    Parker
    "When governments fear the people, there is liberty. When the people fear the government, there is tyranny." Thomas Jefferson

  2. #2
    Member
    Join Date
    Sep 2011
    Location
    Stockton, CA
    Posts
    58
    Thanked: 10

    Default

    is the wood you have already in scale thickness slabs, or just a block? Either way, make sure that the indide faces are FLAT. A piece of glass, granite counter top, marble tile, etc, with sandpaper taped to it works well if you don't have a disc grinder. Lightly glue those two surfaces together with a few drops of wood glue and a piece of printer paper between them. Draw your pattern on the wood, or glue a paper pattern to it. Profile and drill both sides together at once. Use a drill press, its more accurate than your eyes and a hand drill. After drilling and profiling, split them apart. Sand away the glue spots. Start shaping and make your wedge. Finish your scales befoe pinning together. That means all buffing, too. Pin the wedge first, then the pivot. Look up Glenn's (gssixgun) video on pinning scales if you need more advice, its almost 30minutes long, and worth it.


    It doesn't take long once you have done a few, but the first one is always nerve wracking.

    Good luck and take picture!


    -Xander

  3. The Following User Says Thank You to fast14riot For This Useful Post:

    Sterm (08-17-2012)

  4. #3
    The Razor Talker parkerskouson's Avatar
    Join Date
    Jun 2012
    Location
    Las Vegas
    Posts
    623
    Thanked: 75

    Default

    Quote Originally Posted by fast14riot View Post
    is the wood you have already in scale thickness slabs, or just a block? Either way, make sure that the indide faces are FLAT. A piece of glass, granite counter top, marble tile, etc, with sandpaper taped to it works well if you don't have a disc grinder. Lightly glue those two surfaces together with a few drops of wood glue and a piece of printer paper between them. Draw your pattern on the wood, or glue a paper pattern to it. Profile and drill both sides together at once. Use a drill press, its more accurate than your eyes and a hand drill. After drilling and profiling, split them apart. Sand away the glue spots. Start shaping and make your wedge. Finish your scales befoe pinning together. That means all buffing, too. Pin the wedge first, then the pivot. Look up Glenn's (gssixgun) video on pinning scales if you need more advice, its almost 30minutes long, and worth it.


    It doesn't take long once you have done a few, but the first one is always nerve wracking.

    Good luck and take picture!


    -Xander
    I currently have a block of the wood. I do have a disc sander, which will work for flatening. I also have a disc grinder, drill press, which will also be nice. Thanks for the advice!

    I will take a picture!!

    Parker
    "When governments fear the people, there is liberty. When the people fear the government, there is tyranny." Thomas Jefferson

  5. #4
    Member
    Join Date
    Jun 2012
    Location
    Ohio
    Posts
    32
    Thanked: 2

    Default

    If you have access to a table saw or a band saw, I would recommend ripping your blanks to roughly 1/8 inch first. Even with a disc sander, it takes longer than necessary to get the blanks down to thickness. Wood scales IMO often times end up too thick and inflexible. If you plan on using a coping saw to get them to shape, it will also be easier with thinner blanks.
    32t likes this.

  6. #5
    Senior Member blabbermouth
    Join Date
    Jan 2011
    Location
    Roseville,Kali
    Posts
    10,432
    Thanked: 2027

    Default

    JMO, wood is great,wood is wonderfull,but not the best meterial for scales,unless you can buy stabilized wood,which is than a sort of plastic.

  7. #6
    The Razor Talker parkerskouson's Avatar
    Join Date
    Jun 2012
    Location
    Las Vegas
    Posts
    623
    Thanked: 75

    Default

    Quote Originally Posted by pixelfixed View Post
    JMO, wood is great,wood is wonderfull,but not the best meterial for scales,unless you can buy stabilized wood,which is than a sort of plastic.
    I know it is not the best, but in my situation it is the cheapest and looks the best for the price.
    "When governments fear the people, there is liberty. When the people fear the government, there is tyranny." Thomas Jefferson

  8. #7
    Member
    Join Date
    Sep 2011
    Location
    Stockton, CA
    Posts
    58
    Thanked: 10

    Default

    Quote Originally Posted by pixelfixed View Post
    JMO, wood is great,wood is wonderfull,but not the best meterial for scales,unless you can buy stabilized wood,which is than a sort of plastic.
    Curious statement. Why don't you think wood is good for scales?


    -Xander
    parkerskouson likes this.

  9. #8
    Senior Member blabbermouth
    Join Date
    Jan 2011
    Location
    Roseville,Kali
    Posts
    10,432
    Thanked: 2027

    Default

    Quote Originally Posted by fast14riot View Post
    Curious statement. Why don't you think wood is good for scales?


    -Xander
    Was wood used back in the day? (not much) ask yourself why plastic (all phenolics) natural materials such as Horn,Ivory,Bone were used as was bakalite and hard rubber,simple answer,they are impervious to water.
    Stabilized (plastisized wood is a differant animal)
    were the materials of choice

  10. #9
    The Razor Talker parkerskouson's Avatar
    Join Date
    Jun 2012
    Location
    Las Vegas
    Posts
    623
    Thanked: 75

    Default

    I just think that for the cost wood scales look the best
    "When governments fear the people, there is liberty. When the people fear the government, there is tyranny." Thomas Jefferson

  11. #10
    Member
    Join Date
    Sep 2011
    Location
    Stockton, CA
    Posts
    58
    Thanked: 10

    Default

    Quote Originally Posted by pixelfixed View Post
    Was wood used back in the day? (not much) ask yourself why plastic (all phenolics) natural materials such as Horn,Ivory,Bone were used as was bakalite and hard rubber,simple answer,they are impervious to water.
    Stabilized (plastisized wood is a differant animal)
    were the materials of choice
    Yes that explain back then, but not now. They also didn't have polymer finishes, spray on finishes, self leveling finishes. There is no reason nowadays that wood scales should be inferior to any other scale material. I say use wood, or plastic or the boss' clip board! I don't feel any one material is any "better" than the rest as a scale material, just how you work it and finish it is different.

    To the OP, a great way to add a little style to straight grain wood scales is to cut at an angle across the grain, say maybe 20-30 degrees. Walnut is great stuff to work with, I lik either Tru-Oil for a hand rubbed oil finish, or CA glue which can give the glass like finish.


    -Xander

Page 1 of 11 12345 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •